Bosch UGBS Original Instructions Manual page 8

OBJ_BUCH-1720-002.book Page 8 Wednesday, December 21, 2016 9:46 AM
8 | English
 Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
 Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
 Wear personal protective equipment and always wear
safety goggles. Depending on the type of sander and the
application, the wearing of personal protective equipment
such as a dust mask, protective gloves, or hearing protec-
tion, reduces the risk of injuries.
 Wear protective gloves and never touch the running
sanding belt. Danger of injury.
 Connect the machine firmly with the holder or the work
surface, and fasten it against movement. The power tool
can move suddenly.
 The On/Off switch must be well-accessible at all times.
Switching off the machine easily must be possible at all
times.
 Switch the power tool off when it is not in use or after a
power failure.
 Guide the workpiece only against the switched-on ma-
chine and do not switch the machine off until after hav-
ing removed the workpiece. The workpiece can move
suddenly.
Product Description and Specifica-
tions
Intended Use
In conjunction with the parallel and angle guide, the holder is
intended for sanding laths and profiles. The holder may only
be used with the following power tools:
– PBS 75 (0 603 270 0..)
– PBS 75 A (0 603 270 1..)
– PBS 75 AE (0 603 270 6..)
– PBS 75 E (0 603 270 7..)
– GBS 75 AE (0 601 274 7..)
Product Features
The numbering of the product features refers to the illustra-
tion of the holder on the graphics pages.
1 Clamp
2 Holder
3 Set of screw clamps
4 Fastening elements
5 Parallel and angle guide* (2 607 001 079)
6 Bolt hole (PBS 75 A/PBS 75 AE)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
1 609 92A 2GN | (21.12.16)
Technical Data
Holder for belt sander
Article number
Weight (without accessories),
approx.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" complies with the provisions
of Directive 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ECS,
70538 Stuttgart, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering and PT/ECS
Manufacturing
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
 Before any work on the machine itself, pull the mains
plug.
 Ensure secure cable routing. The power tool cable must
not be located near moving parts.
Horizontal Operation (see figure A–C)
Position the power tool with the holder 2 as shown in the fig-
ure.
Mount the holder 2 with the clamp 1 and the fastening ele-
ments 4 to the power tool. Clamp the holder 2 with the set of
screw clamps 3 to a stable bench top.
Additionally, the parallel and angle guide 5 can be mounted;
the threaded holes 6 are the fastening points for the parallel
and angle guide 5.
Vertical Operation (see figures D–E)
Position the power tool with the holder 2 as shown in the fig-
ure.
Mount the holder 2 with the clamp 1 and the fastening ele-
ments 4 to the power tool. Clamp the holder 2 with the set of
screw clamps 3 to a stable bench top.
Additionally, the parallel and angle guide 5 can be mounted;
the threaded holes 6 are the fastening points for the parallel
and angle guide 5.
Ensure that the clamp is stable. Check the clamp regularly.
Keep the distance between the parallel and angle guide 5 and
the abrasive belt small. Adjust the guide if necessary (see fig-
ures C and E).
UGBS
1 608 030 024
kg 0.6
Bosch Power Tools