DSL Operation Mode .................... 13 Command Path Changes ..................13 Data CLI Changes Examples ................15 Version 6.8 Configuration ..................15 Version 7.2.150 Configuration ................21 CLI Voice Changes .................... 31 Simple Voice Configuration Changes Example ............. 31 Version 7.2 Mediant MSBR...
Page 4
Upgrading to Version 7.2 This page is intentionally left blank. Configuration Note Document #: LTRT-23304...
Page 5
Customer Support Customer technical support and services are provided by AudioCodes or by an authorized AudioCodes Service Partner. For more information on how to buy technical support for AudioCodes products and for contact information, please visit our Web site at www.audiocodes.com/support.
Page 6
23304 Added CLI Voice Changes section. Documentation Feedback AudioCodes continually strives to produce high quality documentation. If you have any comments (suggestions or errors) regarding this document, please fill out the Documentation Feedback form on our Web site at http://www.audiocodes.com/downloads.
Version 7.2 are by default configured with a Single Network mode. In addition to the above, this document also includes instructions on how to upgrade device firmware to Version 7.2 and also includes example configuration output for both Version 6.8 and Version 7.2. Version 7.2 Mediant MSBR...
Page 8
Upgrading to Version 7.2 This page is intentionally left blank. Configuration Note Document #: LTRT-23304...
HTTP or HTTPS servers. Upgrade to Version 7.2 needs to be performed from at least Version 6.80.286.002. If the MSBR version is lower than Version 6.80.286.002, the MSBR first needs to be upgraded to this version. Version 7.2 Mediant MSBR...
Page 10
Upgrading to Version 7.2 This page is intentionally left blank. Configuration Note Document #: LTRT-23304...
From the Device Actions drop-down list, select Software Upgrade Wizard: Figure 3-1: Software Upgrade Wizard Choose a file to load and click the Load File button. Figure 3-2: Load File When the file has finished loading, click the Reset button. Version 7.2 Mediant MSBR...
Upgrading to Version 7.2 Following the upgrade, specific commands will be located in different paths. If management software is used, for example a CWMP server, make sure that you have copied a Version 7.2.150 or later configuration file to the Management server. It is recommended to download the new configuration to the Management Software after the MSBR have been upgraded.
Page 14
Upgrading to Version 7.2 The following table describes these changes in Show commands: Table 4-2: Show Commands Changes Command Description Version 6.8 Path Version 7.2 Path show version Displays software Show system version Show version version. show system date Displays current Show system date show system clock or show system...
Page 17
"WAN Copper" no ipv6 enable speed auto duplex auto no service dhcp ip dns server static napt firewall enable no shutdown exit interface Fiber 0/1 no ip address mtu auto Version 7.2 Mediant MSBR...
Page 18
Upgrading to Version 7.2 desc "WAN Fiber" no ipv6 enable no service dhcp ip dns server static no shutdown exit interface dsl 0/2 #DSL configuration is automatic #Termination cpe mode ADSL auto-switch-attempts vdsl 2 vdsl-v43 0 adsl 2 no shutdown exit interface EFM 0/2 #This interface is DISABLED due to physical layer configuration...
Page 19
100 beacon dtim-period 1 beacon period 100 fragment threshold 2346 cts mode none cts type burst num 3 burst time rts threshold 2346 shutdown exit interface pppoe 0 firewall enable napt mtu auto Version 7.2 Mediant MSBR...
Page 20
Upgrading to Version 7.2 ppp user tim obscured-pass Vhc2aWtpb2lr ppp authentication chap no ppp authentication ms-chap no ppp authentication ms-chap-v2 no ppp authentication pap ppp lcp-echo 6 5 no ppp compression ip address auto no ipv6 address ip dns server auto underlying GigabitEthernet 0/0 network wan no shutdown...
# The following line is not activated poe-table 3 port-enable enable no activate exit # The following line is not activated poe-table 4 port-enable enable no activate exit # The following line is not activated poe-table 5 Version 7.2 Mediant MSBR...
Page 22
Upgrading to Version 7.2 port-enable enable no activate exit # The following line is not activated poe-table 6 port-enable enable no activate exit # The following line is not activated poe-table 7 port-enable enable no activate exit # The following line is not activated poe-table 8 port-enable enable no activate...
Page 23
10486144 energy-detector-cmd 587202560 activate exit gateway digital rp-network-domains 1 name "dsn" activate exit gateway digital rp-network-domains 2 name "dod" activate exit gateway digital rp-network-domains 3 name "drsn" activate exit gateway digital rp-network-domains 5 name "uc" Version 7.2 Mediant MSBR...
Page 24
Upgrading to Version 7.2 activate exit gateway digital rp-network-domains 7 name "cuc" activate exit gateway analog authentication 0 user-name "1001" password C35/aHw+T31zfQ== obscured activate exit gateway analog authentication 1 user-name "" activate exit gateway analog authentication 2 user-name "" activate exit gateway analog authentication 3 user-name ""...
Page 25
60 session-timeout 15 session-limit 5 cli-session-limit -1 exit exit ## TROUBLESHOOT configure troubleshoot activity-log config-changes off files-loading off device-reset off flash-burning off software-update off unauthorized-access off sensitive-config-changes off login-and-logout off cli-commands-log off action-execute off activate exit Version 7.2 Mediant MSBR...
Page 26
Upgrading to Version 7.2 activate exit # DATA ROUTER configure data radio shutdown interface GigabitEthernet 0/0 ip address dhcp no ip dhcp-client default-route mtu auto desc "WAN Copper" no ipv6 enable speed auto duplex auto no service dhcp ip dns server static napt firewall enable no shutdown...
Page 27
1 #This interface is DISABLED due to physical layer configuration no ip address bridge-group 1 mtu auto desc "LAN Wireless 802.11n Access Point" no ipv6 enable no service dhcp ssid MSBR Version 7.2 Mediant MSBR...
Page 28
Upgrading to Version 7.2 broadcast security mode NONE no security mac mode mode ngb channel width 40/20 channel auto power 100 beacon dtim-period 1 beacon period 100 fragment threshold 2346 cts mode none cts type burst num 3 burst time rts threshold 2346 shutdown exit...
Page 29
Configuration Note 5. Data CLI Changes Examples ip route 10.4.2.102 255.255.255.255 10.31.0.1 GigabitEthernet 0/0 1 ip domain name home ip domain localhost msbr pm sample-interval minute 5 pm sample-interval seconds 15 exit Version 7.2 Mediant MSBR...
Page 30
Upgrading to Version 7.2 This page is intentionally left blank. Configuration Note Document #: LTRT-23304...
The following section compares by sections, the changes in the CLI Voice commands. It is also recommended to review the CLI Configuration Guide to learn the new Voice commands. Simple Voice Configuration Changes Example In this configuration, the following topology is configured: Figure 6-1: Configured Topology Version 7.2 Mediant MSBR...
Page 32
Upgrading to Version 7.2 In the following table, the left column lists Version 6.8 commands, and the right column lists the equivalent command in Version 7.2. Both configurations achieve the same goal. The table is arranged in the order of the Version 7.2 CLI script, while the Version 6.8 commands is in order as it appears in the output of the "show run"...