Related Manuals for Cornelius Cascata180
Summary of Contents for Cornelius Cascata180
- Page 1 Cascata180 Nitro-Coffee Dispenser Installation, Operation & Service Manual Publication Number: 890729106 Revision Date: Jun. 2017 Revision: Beta-1.1 CORNELIUS INC...
- Page 2 To familiarize yourself with the latest versions of this manual or other documents, or should you need technical supports for any Cornelius product, please contact local supporting technicians of Cornelius or obtain assistance through: CORNELIUS INC, 12 Xin Tai Road, TEDA, Tianjin, PRC, 300457 www.cornelius.com.cn...
-
Page 3: Table Of Contents
Routine maintenance ........................... - 12 - Washing and disinfection of piping system ..................- 13 - Descaling of piping system ......................... - 15 - Cleaning the filter screen ........................- 15 - Troubleshooting ............................- 16 - - 2 - © 2017, Cornelius Inc. -
Page 4: Safety
Danger: Before service, please be sure to disconnect power supply and water supply, empty the regulator tank and quit all operations that have been executed by the user or it may cause accidents. - 3 - © 2017, Cornelius Inc. - Page 5 - 4 - © 2017, Cornelius Inc.
-
Page 6: General
The body of this product is intended to be installed under the counter and the valve tower which are equipped with two taps are intended to be installed on the counter. - 5 - © 2017, Cornelius Inc. -
Page 7: Product Specifications, Parameters And Explanation
Volume of coffee keg Warranty terms This product is covered by the commercial warranty of Cornelius and subject to all constraints and limits of the commercial warranty. Cornelius will not be responsible for servicing, replacement and other services in case of loss of or damage to the product arising from (but not limited to) the following: (1) use of the product in conditions other than required normal conditions and for purposes other than intended purpose;... -
Page 8: Installation
Remove any debris on heat exchange vent on the top and in the rear of the machine. To avoid overheating of and damage to the pre-cooling body, the top and external walls of the device must be at least75mm away from the objects around it. - 7 - © 2017, Cornelius Inc. -
Page 9: Installation Steps
Connect the “a” and “b” of the strainer to the coffee machine as above graphic. After the coffee machine is placed suitable position and then fix the strainer under the table. - 8 - © 2017, Cornelius Inc. -
Page 10: Connect Nitrogen Supply
2. Tighten the lid of coffee keg and connect the keg to the nitrogen and liquid pipelines of the body through white/black connectors respectively. 3. Place the coffee keg onto the weighing platform. - 9 - © 2017, Cornelius Inc. -
Page 11: Device Commissioning
Warning -pipe joints, clamps and threads must be properly installed; otherwise, leakage of water or nitrogen may occur during use. Attention -the device should be installed in the area where it is used and where the trained professional service personnel have easy access to it. Operation - 10 - © 2017, Cornelius Inc. -
Page 12: Startup And Shutdown Of The Device
Close the cylinder master switch and power switch at night when the business is closed. Warning - the pre-prepared cold-brew coffee should not contain particles of which diameter is larger than 0.2mm, or it may cause clogging in the device. - 11 - © 2017, Cornelius Inc. -
Page 13: Washing And Maintenance
® and drain the keg. Then fill 9 L of (c) KAY disinfectant (100ppm) into the keg, shake the keg rigorously to ensure uniform contact of the disinfectant with the inner wall of - 12 - © 2017, Cornelius Inc. -
Page 14: Washing And Disinfection Of Piping System
Open the two taps to empty the pipes of the system, close the taps until coffee keg is emptied and a large volume of gas emits. Step 2 - flushing with drinking water: - 13 - © 2017, Cornelius Inc. - Page 15 - 14 - © 2017, Cornelius Inc.
-
Page 16: Descaling Of Piping System
1. Remove the air inlet filter from the device. 2. Use a vacuum cleaner or soft brush to clean the dust on filter screen. 3. Put the filter back on the device. - 15 - © 2017, Cornelius Inc. -
Page 17: Troubleshooting
Please contact device servicing personnel Leakage on the device Turn off the main power supply and Damage of parts close the main nitrogen valve. Please contact device servicing personnel - 16 - © 2017, Cornelius Inc. - Page 18 - 17 - © 2017, Cornelius Inc.
- Page 19 - 18 - © 2017, Cornelius Inc.
- Page 20 Cornelius (Tianjin) Co., Ltd. www.cornelius.com.cn...