Whirlpool GY397LXU Dimensions

®
30" Slide-in Electric Range
PRODUCT MODEL NUMBERS
GY397LXU
GY399LXU
Electrical: This range is manufactured with the
neutral terminal connected to the cabinet. Use a 3-
wire, UL listed, 40- or 50-amp power supply cord
(pigtail) (see Range Rating chart below). If local
codes do not permit ground through the neutral,
use a 4-wire power supply cord rated at 250 volts,
40- or 50-amps and investigaed for use with
ranges. A time-delay fuse or circuit breaker is
recommended. The model/serial rating plate is
located on the oven frame behind the storage
drawer panel.
Range Rating
120/240 Volts 120/208 Volts
8.8 - 16.5 KW 7.8 - 12.5 KW
16.6 - 22.5 KW 12.6 - 18.5 KW
COUNTERTOP PREPERATION
The cooktop sides of the slide-in range fit over the cutout
edge of your countertop.
If you have a square finish (flat) countertop and the
opening width is 30" (76.2 cm), no countertop
preparation is required.
Formed front-edged countertops: Must have molded edge
shaved flat 3/8" (1.0 cm) from each front corner of
opening.
Tile countertops may need trim cut back 3/8" (1.0 cm)
from each front corner and/or rounded edge flattened.
If countertop opening width is greater than
30" (76.2 cm), adjust the 3/8" (1.0 cm) dimension.
Countertop must be level. Place level on countertop, first
side to side; then front to back. If countertop is not level,
range will not be level. Oven must be level for
satisfactory baking conditions.
30"
(76.2 cm)
opening
width
30-3/4" (78.1 cm)
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
OVERALL DIMENSIONS
Specified Rating
of Power Supply
Cord Kit and
Circuit
Protection
Amps
40 or 50
50
CABINET OPENING DIMENSIONS
Cabinet opening dimensions
shown are for:
25" (63.5 cm) countertop
depth, 24" (61.0 cm) base
cabinet depth, 36" (91.4 cm)
countertop height
3/8"
(1.0 cm)
Formed or tiled countertop
trimmed 1/2" (1.3 cm) back
at front corners of
countertop opening.
*NOTE: 24" (61 cm) min. when bottom of wood or metal cabinet is protected by not less than 1/4" (6.4 mm)
flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel,
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) min. clearance between the top of the
cooking platform and the bottom of an unprotected wood or metal cabinet.
**30-7/8" (78.4 cm) with side panels.
30-3/4" (78.1 cm)
cooktop width
35-3/4" (90.8 cm)
cooktop height
23-3/4"
with leveling
(60.3 cm)
legs screwed all
the way in
1" (2.5 cm)
spacer
28-5/16"
(71.9 cm)
depth with
handle
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
29-7/8" (75.9 cm) width*
*30-3/4" (78.1 cm) with side panels
13" (33.0 cm) max.
upper cabinet depth
30" (76.2 cm) min.
cabinet opening width
3/8" (9.5 cm)
radius both
corners
30" (76.2 cm)
opening width**
junction box – 5.5" (14 cm min.)
from either cabinet, 10" (25.4 cm)
max. from floor.
Cabinet door or
hinge should not
extend into cutout.
For minimum
clearance to the
top of the cooktop,
see NOTE.*
23-1/4" (59.1 cm)
opening depth
Ref. 8101P750-60
04-09-08