Display; Start; Off/Cancel; Clock - Whirlpool 9762365A Use And Care Manual

Style 1 - Electronic Oven Control
When power is first supplied to the appliance, "12:00 PM" will
appear on the display. See "Clock" section to set time of day.
If "12:00 PM" appears at any other time, a power failure has
occurred. Press OFF/CANCEL and reset the clock if needed.
When the oven is not in use, the display shows the time of day.
Styles 2, 3 & 4 - Electronic Oven Controls
When power is first supplied to the appliance, "PF" or a flashing
time will appear on the display. Press OFF/CANCEL to clear the

display.

If "PF" or a flashing time appears at any other time, a power
failure has occurred. Press OFF/CANCEL and reset the clock if
needed.
When the oven is not in use, the display shows the time of day.
When performing a timed cook function, the display will show
either hours and minutes, or minutes and seconds.
Style 1 - Electronic Oven Control
The Start pad begins any oven function. The display will show
SET TEMP OR TIME OR PUSH START.
Styles 2, 3 & 4 - Electronic Oven Controls
The Start pad begins any oven function. If the Start pad is not
pressed within 5 seconds after pressing a function pad, the
"START?" or "?" indicator light will appear on the display (on
some models).
If the Start pad is not pressed within 5 minutes after pressing a
function pad, the oven display will return to the time of day mode
and the programmed function will be canceled.

Off/Cancel

The Off/Cancel pad stops any function except the Clock, Timer,
Control Lock or Warm Drawer (on some models).
On some models, this is a 12-hour clock that shows a.m. and
p.m.
To Set:
Before setting, make sure the oven and Timer are off.
1. Press CLOCK.
2. Depending on your model, press the HR or MIN or TIME/
TEMP "up" or "down" arrow pads to set the time of day,
including a.m. or p.m.
3. Press CLOCK.
12
Display

Start

Clock

Tones are audible signals, indicating the following:
Basic Functions
One tone
Valid pad press
Oven is preheating (long tone)
Function has been entered
Reminder (on some models), repeating each minute after the
end-of-cycle tones
Three tones
Invalid pad press
Four tones
End of cycle
Style 1 - Electronic Oven Control
Reminder Tones: Reminder tones may be turned off. On some
models, press and hold BAKE for 5 seconds. REMINDER TONES
OFF will appear on the display. Repeat to turn reminder tones
back on, and REMINDER TONES ON will appear on the display.
All Tones: All of the above tones are preset on.
To disable tones, press and hold CLOCK for 5 seconds. Repeat
to turn tones back on.
To Turn Off/On: Press and hold CLOCK for 5 seconds. A tone
will sound when changing tones from OFF to ON. ALL SOUNDS
OFF will appear on the display. Repeat to turn tones on, and ALL
SOUNDS ON will appear on the display.
Tone Pitch: The pitch is preset at high, but can be changed to
low.
To Change: Press and hold BROIL for 5 seconds. A tone will
sound, and TONE PITCH LOW will appear on the display. Repeat
to change and TONE PITCH HIGH will appear on display.
End of Cycle Tones: Press and hold CONVECT for 5 seconds to
turn END OF CYCLE TONES off. Press and hold CONVECT for
5 seconds to turn END OF CYCLE TONES on.
Key Press Tone: Press and hold WARM (Cooking Options) for
5 seconds, and KEY PRESS TONES OFF will appear on the
display. Press and hold WARM for 5 seconds, and KEY PRESS
TONES ON will appear on the display.
Style 2 - Electronic Oven Control
Reminder Tones: Reminder tones may be turned off. On some
models, press and hold TIMER SET for 5 seconds. "rEP OFF" or
"OFF" will appear in the display. Repeat to turn reminder tones
back on, and "rEP ON" or "ON" will appear in the display.
All Tones: All of the above tones are preset on. All except the
end-of-cycle tones can be turned off.
To Turn Off/On: Press and hold STOP TIME for 5 seconds. A
tone will sound, and "Snd OFF" will appear on the display. Press
and hold COOK TIME for 5 seconds to turn tones on, and "Snd
ON" will appear on the display.
Tone Pitch: The pitch is preset at high, but can be changed to
low.
To Change: Press and hold DELAY START for 5 seconds. A tone
will sound, and "Snd LO" will appear on the display. Repeat to
change, and "Snd HI" will appear on display.
Style 3 & 4 - Electronic Oven Control
Refer to Basic Functions in the "Tones" section.

Tones