Canceling A Cycle; Changing A Cycle Or Setting; Adding Items During A Cycle; Option Selections - Whirlpool Series 1000 Use And Care Manual

Use this cycle for rinsing
dishes, glasses, and
silverware that will not be
washed right away.
Pre- Rinse Main Rinse
Wash Wash
† A small amount of water runs through the pump to
remove soil particles.
Series 940 and 960 only.
††

Canceling a Cycle

Anytime during a cycle, press
CANCEL/DRAIN glows. The dishwasher pauses for about 5
seconds and starts a 2 minute drain (if needed). Let the
dishwasher drain completely. The light goes off when the
dishwasher finishes the drain.
To stop the drain
You can press Cancel/Drain again to stop the drain immediately.
Remember to drain the dishwasher before starting a new cycle.
NOTE: A small amount of water remains in the dishwasher. This
is normal.
To clear the indicators
Press Cancel/Drain before starting the dishwasher to clear all
options and cycles.

Changing a Cycle or Setting

During the first minute of a cycle
Press a new cycle and/or options.
After the first minute of a cycle
1. Press
CANCEL/DRAIN glows. The dishwasher pauses for 5
seconds and starts a 2 minute drain (if needed). Let the
dishwasher drain completely.
2. Check the detergent dispensers. If the main wash cup has
opened and the detergent washed away, refill the cups as
needed.
3. Close the door.
4. Press a new cycle and/or options.
Do not use
detergent
with this
cycle.
† Final Dry Time
Purge
Rinse (min)
10

Adding Items During a Cycle

You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the main wash
section is still closed, you can add items.
To add items
1. Lift up the door latch to stop the cycle. Wait for the spraying
Water
action to stop before opening the door.
Usage
2. Open the door. If the main wash detergent dispenser is still
(gal/L)
closed, add the item.
2.2/10.0
3. Close the door, but do not latch it. Wait 30 seconds for the air
in the dishwasher to warm up. This reduces the amount of
moisture escaping from the vent when restarting a cycle.
4. Close the door firmly until it latches. The dishwasher resumes
the cycle after about a 5 second pause.
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off.
Select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
any time before drying begins.
After a wash cycle, the dishwasher remembers the options used
and uses the same options in the next wash cycle, unless you
select new options or press Cancel/Drain.
POWERSCOUR™ feature (on some models)
Select this high-temperature option for improved cleaning of
heavily soiled dishes. Selecting this option adds heat, water and
time to the wash cycle. Heating the water helps improve washing
results.
The Pots-N-Pans cycle, with the POWERSCOUR feature, is
recommended for baked-on soil.
NOTE: The POWERSCOUR feature is an option with Pots-N-
Pans, Heavy and Normal.
High Temp Wash (on some models)
Select this option to heat the water to 140°F (60°C) in the main
wash. This option adds heat and wash time. Heating the water
helps improve washing results.
NOTE: The Pots-N-Pans and Heavy cycles automatically use this
option. High Temp Wash is an option with Normal, Low Energy,
Low Energy/China and Crystal/China.
Air Dry
Select this option to dry dishes without heat and save energy.
The dishes take longer to dry and some spotting can occur.

Option Selections

13