Advertisement
Quick Links
Advertisement
Summary of Contents for JDS Uniphase Talk-N-Trace TM-110
- Page 1 Talk-N-Tracef Communication and Tracing Set User's Guide www.jdsu.com/know...
- Page 3 ON / RING BUTTON When unit is off, pressing this button turns on power to talk circuitry. When unit on, pressing this button causes the ringers on the other end(s) of the wire to ring as long as the button is held down/up to approx.
- Page 4 Warning! Do not touch to live AC circuits. This could cause an extreme shock hazard and damage a Talk-N-Trace™. Description The Talk-N-Trace™ is a point-to-point, wired, full duplex, self-powered talk set. The included headset is an over-the-ear style for hands-free use. Any standard cell phone headset with 2.5mm plug can also be used.
- Page 5 Features • Full duplex, hands-free, self powered communications • Built-in ringer and ability to signal other • Compact size with belt clip, small enough to wear on belt or carry in pocket • Auto-off after hour • Low battery indicator •...
- Page 6 Trace Features An identification (ID) banana jack is located on the side opposite the RJ jack to facilitate the identification of wires while two Talk- N-Trace™ units are connected together by a communications pair. A standard test lead set has been included to connect the banana jacks to wires to be tested.
- Page 7 Instructions for Use Connect cord set provided or other cable with standard modular phone plug to jack on the side of Talk-N-Trace™. Connect headset to 2.5mm phone jack at top. Connect Talk-N-Trace™ to wire pair to be used for connecting the two Talk-N- Trace™...
- Page 8 each end and locate wire end. When both probes are connected to the same wire, both ends will ring. Turn off unit when conversation is concluded by pressing “OFF” button. Unit will turn off after approximately one hour if no button is pressed. Pressing “ON”...
-
Page 9: Battery Installation
Battery Installation Before first use or when the battery low LED is on, install a 9 volt alkaline battery as follows: Remove rubber cap from bottom of unit by peeling it off from any corner. Unsnap battery cable from old battery. Slide battery out of cavity and discard properly. - Page 10 Models, options & accessories Ordering Description number KP0 Talk-N-Trace communication and tracing set in a nylon pouch TM0 Talk-N-Trace communication and tracing set, two mini headsets LB40B, 48” cord set RJ to alligator (2), nylon pouch LB5 Cloth braided RJ to angled bed-of-nails with piercing clips - 48”...
- Page 11 Specifications Electrical Return Loss: >4db @ 00ohms Cable Length: ,000 to 5,000 ft (Cable type dependent) Battery life (9V Alkaline) - Operating: 5 hours, typical Standby: years, typical Environmental Temperature – Operating: -0 to 0 C Storage: -40 to C Physical Length: 5.5 in (. cm) Width: .90 in (4.8 cm)
-
Page 12: Customer Services
Customer Services This section provides a description of customer services available through JDSU (including returns policies and procedures) and warranty information. Customer Service (Standard Services) Customer Service accompanies the sale of every JDSU product. Customer Service services include: • Technical Assistance (Business Hour) •... - Page 13 manufactured equipment. This ensures products meet all published specifications, including any applicable product updates. Calibration — JDSU’s calibration methods are ISO approved and based on national standards. Factory Upgrades — Any unit returned for a hardware feature enhancement will also receive applicable product updates and will be thoroughly tested, ensuring peak performance of the complete feature set.
- Page 14 problem or service requested. • The name and telephone number of the person to contact regarding questions about the repair. • The return authorization (RA) number (US customers), or reference number (European Customers). If possible, return the equipment using the original shipping container and material.
-
Page 15: Warranty Information
Warranty Information JDSU guarantees that its products will be free of all defects in material and workmanship. This warranty extends for the period of 2 months for test instruments and months for cables from date of manufacture or purchase (proof of purchase required). - Page 16 is reused, recycled, or disposed of in an environmentally friendly manner, and in compliance with all applicable national and international waste legislation. It is the responsibility of the equipment owner to return the equipment to JDSU for appropriate disposal. If the equipment was imported by a reseller whose name or logo is marked on the equipment, then the owner should return the equipment...
- Page 17 Notes:...
- Page 18 Notes:...
- Page 20 www.jdsu.com/know Document Information Doc. # TU9837 Revision 500, 06-08 English...