Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for VTech Toot-Toot Drivers Twist & Race Tower
Summary of Contents for VTech Toot-Toot Drivers Twist & Race Tower
- Page 1 Parent’s Guide Twist & Race Tower 91-003870-001...
- Page 2 Grow with VTech(101x127)bw1P-V2.pdf 1 08/18/2014 9:29:01...
- Page 3 INTRODUCTION Thank you for purchasing the Toot-Toot Drivers Twist & Race Tower! Let’s go for a super spiral ride! Assemble the set with two side-by-side ramps, or put it all together for an amazing three-foot corkscrew tower! Place the Race Car on the launcher at the start line. Press the trophy to launch the vehicle through the switch track.
- Page 4 INCLUDED IN THIS PACKAGE Toot-Toot Drivers Twist & Race Tower ® Label sheet Parent’s guide One SmartPoint Race Car One launcher ™ One trophy One switch track Six track connectors One start sign...
- Page 5 One helicopter bracket One helicopter One pillar One arch One Y track One flag One male/female One gate adaptor track...
- Page 6 Four spiral tracks One trap door Base segments A & B Support columns A & B Seven screws...
- Page 7 WARNING All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties and packaging screws are not part of this toy and should be discarded for your child’s safety. NOTE Please keep this parent’s guide as it contains important information. CAUTION Adult assembly required.
- Page 8 BATTERY NOTICE • Use new alkaline batteries or fully charged NI-MH (Nickel Metal- hydride) rechargeable batteries for best performance. • Use only batteries of the same or equivalent type as recommended. • Do not mix different types of batteries: alkaline, standard (carbon- zinc) or rechargeable, or new and used batteries. • Do not use damaged batteries. • Insert batteries with the correct polarity. • Do not short-circuit the battery terminals. • Remove exhausted batteries from the toy. • Remove batteries during long periods of non-use. • Do not dispose of batteries in fire. • Do not charge non-rechargeable batteries. • Remove rechargeable batteries from the toy before charging (if removable).
- Page 9 LABEL APPLICATION Please securely stick the labels to the play set as indicated on the following pages: 0:54:03 Start Start Start +0.11 +1.85 +1.02 +2.09 +0.08 +0.89 Start Start Start Tyres Tyres...
- Page 11 ASSEMBLY INSTRUCTIONS With the Toot-Toot Drivers Twist & Race Tower, safety comes ® first. Adult assembly required. For your child’s safety, do not let them play with this toy until it is fully assembled. SMALL COMPONENT ASSEMBLY 1. Clip the Helicopter onto the Bracket and insert the Pillar into the bottom of the Bracket.
- Page 12 4. Snap the Trap Door into the Spiral Track. 5. Insert the Switch Track in the slot of the Y Track. 6. Connect Base Segments A & B and secure with four Screws. 7. Insert Support Column A into the Base, turn over and secure with three Screws.
- Page 13 SPIRAL TOWER ASSEMBLY 1. Insert Support Column B into the top of Support Column A. 2. Each section of Spiral Track has two numbered Brackets. Starting with Track A at the bottom, match each Bracket with the tab of the same number.
- Page 14 3. Starting with Track A at the bottom, snap each pair of Brackets onto the matching tabs. Repeat the process with Track B, C and D. 4. Use the Track Connectors to join the Spiral Track segments.
- Page 15 5. Insert the Launcher on the top of the Pillar. Use the Track Connector to secure the Launcher to the topmost Track. 6. Connect the Y Track to Base Segment A, and use a Track Connector to join the tracks securely. 7. Insert the Flag into the slot of the Base to fasten the track. 8.
- Page 16 9. Connect the Adaptor Track to Base Segment B. Once you’ve completed the above steps, you are ready to play with the Twist & Race Tower! You can connect the play set to other Toot-Toot Drivers play sets (each sold separately). For ®...
- Page 17 3. Place the Launcher on top of Support Column B. 4. Use the Track Connectors to join the Y Track, Spiral Track and Launcher together. If you cannot connect the Y Track, adjust the insertion angle of the Launcher to assemble. 5.
- Page 18 6. Attach one Track Connector to the end of the Spiral Track. 7. Add the Helicopter and Gate to the track. 8. Connect the Adaptor Track to the play set. Once you’ve completed the above steps, you are ready to play!
- Page 19 EXPAND & EXPLORE Connect to the Toot-Toot Drivers Track Set (as shown below) or ® other play sets (each sold separately) to expand your Twist & Race Tower and inspire creativity. PRODUCT FEATURES Race Car 1. On/Off Switch To turn the Race Car On, slide the On/Off Switch to the On position.
- Page 20 ACTIVITIES Race Car 1. Slide the On/Off Switch to turn the Race Car On. You will hear a song, fun phrases and sounds. The light will flash with the sounds. 2. Press the Face Button to hear fun sounds, songs, phrases and melodies.
- Page 21 5. For added fun, the Race Car interacts with the Toot-Toot Drivers Twist & Race Tower. ® Simply put the Race Car on one of the play set’s five SmartPoint locations to see the Race Car’s light flash and to hear fun sounds, short tunes and phrases.
- Page 22 CARE & MAINTENANCE 1. Keep the unit clean by wiping it with a slightly damp cloth. 2. Keep the unit out of direct sunlight and away from any direct heat sources. 3. Remove the batteries if the unit will not be in use for an extended period of time.
- Page 23 CONSUMER SERVICES Creating and developing VTech products is accompanied by a responsibility that we at VTech take very seriously. We make every ® effort to ensure the accuracy of the information, which forms the value of our products. However, errors sometimes can occur. It is...
- Page 24 Visit our website for more information about our products, downloads, resources and more. www.vtech.co.uk www.vtech.com.au TM & © 2020 VTech Holdings Limited. All rights reserved. Printed in China. 91-003870-001...