Table of Contents
Advertisement
OP-ER'ATING
I N S T R U C T I O N S
Press
1 , 2 3,
or 4 on the Handset to select
MEMORY
a ringer type. The Handset will emit the cor-
The 917ADXcordless phone can store up
responding ringer tone.
to10 frequently dialed numbers in memory.
Press OFF on the Handset to exit pro-
Memory Dial numbers must be stored us-
yamming.
ing the Handset, but can be recalled from ei-
ther the Base Unit or the Handset.
WRNlNG OFF THE HANDSET RINGER
TO STORE A NUMBER INTO MEMORY
The Handset must
)e OFF
I
Press PRGIPRV on
he Handset
I
Press
#
or
'
key on
he Handset
I
Press 5 to turn off
he ringer
I
Press OFF key to
!xit
The Handset must be OFF
Press PRGIPRV on the Handset
TO PROGRAM
THE RING TYPE
MEMORY DIALING
I
This control switch is located on the right
and edge of Base Unit.
1
Select HIGH, LOW or OFF setting.
:HECKING.THE HANDSET RINGER
'
( To check the ringer type which is currently
rogrammed, do the following:
1
Handset must be OFF
I
Press PRWPRV on the Handset
1
Press
#
key on the Handset
1
Press 0 on the Handset. The phone will
ring once to show ringer selected.
1
Press OFF key to exit
.Press
the Memory
Location key where the
phone number will be
stored (0-9)
. D i a l
the number you
want to store. The num-
ber can be up to 16
digits long
.Press
MEM on the
Handset to complete
programming
. I f
programming has
been successful,a
happy tone will be
generated.
If programming was unsuccessful, a sad
tone is generated.
If the phone is left unattended in program
mode for longer than 30 seconds, it will gen-
erate a sad tone and automatically exit pro-
gram mode.
Write down the phone number you as-
signed to each Memory Location key on the
directory card in the Base Unit cradle.
-
-
TO DIAL A NUMBER FROM MEMORY
You can Memory Dial from either the
Handset or the Base Unit
.
O P E R A T I N G
I
Press PHONE (on the Handset) or SPKR
(on the Base Unit) to get a dial tone
Press MEM and the Memory Location key
(0-9)
For example, to dial the number you as-
signed to key ' 8 ' , you would press PHONE,
MEM,
8
(on the Handset), or SPKR, MEM, 8
(on the Base Unit).
TO CHANGE OR REPLACE A STORED
NUMBER
You can change or replace a stored phone
number by storing a new number in its place.
See TO STORE A NUMBER INTO MEMORY.
TO ERASE STORED NUMBER
FROM MEMORY
The Handset must be OFF.
Press PRGIPRV on the Handset.
Press the Memory Location of the phone
number to be erased.
Press MEM on the handset to complete
programming.
STORING PAUSES IN MEMORY
I!
II
N S T R U C T I O N S
i ,
To insert a pause while programming a
Memory Dial number, do the following on the
Handset:
Press PRGIPRV on the Handset
Press the Memory Location key where the
phone number will be stored (0-9)
Dial the number you want to store, press-
,
ing HOLD at the appropriate point (to insert a
I
2 second pause). The number can be up to
16 digits long. Each press of HOLD is treated
as stored digit.
For longer pauses, press HOLD two or
more times. Each press makes the pause 2
seconds longer and is treated as a stored
digit.
Press MEM on the Handset to complete
programming.
For example, if your phone is connected to
a PBX, you can store the PBX access num-
ber and a pause before the phone number.
To store 9-PAUSE-555-1234, in Memory Lo-
cation 8, you would:
Press PRWPRV
Press
8
Advertisement
Table of Contents
