Related Manuals for Toro VS-70
Summary of Contents for Toro VS-70
- Page 1 Form No. 3377-563 Rev B VS-70 and VS-80 Screed Model No. 68054—Serial No. 313000001 and Up Model No. 68055—Serial No. 313000001 and Up g021465 *3377-563* B Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Introduction
Whenever you need service, genuine Toro parts, or additional WARNING information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the CALIFORNIA model and serial numbers on the product. Write the numbers Proposition 65 Warning in the space provided. -
Page 3: Table Of Contents
Contents Safety Introduction ..............2 Improper use or maintenance by the operator or owner Safety ................3 can result in injury. To reduce the potential for injury, Safe Operating Practices........... 3 comply with these safety instructions and always Safety and Instructional Decals ......... 5 pay attention to the safety alert symbol , which means: Caution , Warning , or Danger —personal safety... - Page 4 Make any necessary repairs to the machine before starting. are no obstacles in close proximity to the operator. Only • Use only genuine Toro replacement parts to ensure that operate the unit in areas where there is sufficient clearance original standards are maintained.
-
Page 5: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 117–2718 125–8192 7. Explosion hazard—stop the engine and 1. Read the Operator’s Manual for 4. -
Page 6: Setup
Setup Installing the Handlebar and Throttle Cable No Parts Required Procedure g022042 1. Slide the handlebar into position (Figure 3). Figure 4 1. Cable fitting 4. Cable 2. Washer 5. Cable anchor 3. Nut 6. Cable stop 5. Move the assembly into place, let the cable stop slide into place, and tighten the cable fitting and nut;... -
Page 7: Product Overview
Product Overview Controls Become familiar with all the engine controls before you start and operate the machine. Engine Controls g021466 Figure 6 1. Throttle lever 4. Lift handle g021468 2. handle bar 5. Board clamp Figure 7 3. Engine 6. Aluminum board 1. - Page 8 Choke Lever The choke lever (Figure 10) is required when starting a cold engine. Before pulling on the recoil-start handle, move the choke lever to the closed position. Once the engine is running, move the choke lever to the open position. Do not use the choke if the engine is already warmed up or the air temperature is high.
-
Page 9: Specifications
Rotate the On/Off switch to the Off position to stop the engine. g021471 Figure 12 Specifications Note: Specifications and design are subject to change without notice. VS-70 VS-80 Width (without screed board) 70.0 cm (27.5 inch) 89.0 cm (35.0 inch) Length 119.4 cm (47.0 inch) -
Page 10: Operation
Operation Important: Before operating the machine, check the • Use the resting position when leaving the machine. fuel and oil levels, and remove debris from the machine. (Figure 14). Never leave the engine running while the machine is in the rest position. Always set the machine on a flat surface. -
Page 11: Adding Fuel
• Use the gas-filling position whenever you fill the gas DANGER tank (Figure 15). With a firm hand on the shaft of the In certain conditions, gasoline is extremely machine and a gas can next to the operator, unscrew the flammable and highly explosive. - Page 12 Filling the Fuel Tank WARNING Fuel tank capacity: 0.65L (0.172 US gallon) Gasoline is harmful or fatal if swallowed. Long-term exposure to vapors can cause serious injury and Important: The unused space in the tank allows the illness. gasoline to expand with changes in temperature. Do not fill the fuel tank completely full.
-
Page 13: Checking The Engine Oil Level
Figure 18 3. Press the priming bulb repeatedly until fuel can be seen in the priming bulb (Figure 9). Note: Toro Premium Engine Oil is available from your 4. Turn the engine switch to the On position. Authorized Toro Dealer. -
Page 14: Screeding A Concrete Surface
Note: Return the recoil-start handle gently. Installing the Aluminum Screed Board Note: Only use equilateral triangle aluminum screed boards designed for this machine. Screed board widths: VS-70 VS-80 1.2 meters (4 feet) 1.8 meters (6 feet) 2.4 meters (8 feet) 3.0 meters (10 feet) x... -
Page 15: Transporting The Machine
Note: To remove the screed board, reverse the steps 7. At the end of the screed pass, move the engine throttle of this procedure. to the idle position and allow the engine to idle for 1 minute. Leveling the Concrete Surface 8. -
Page 16: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Change the oil. After the first 50 hours • Check the engine oil level. • Inspect the air cleaner elements. Before each use or daily •... -
Page 17: Premaintenance Procedures
CAUTION Disconnect the wire from the spark plug before you do any maintenance. Set the wire aside so that it does not accidentally contact the spark plug. Premaintenance 2. Pull the spark-plug wire off the terminal of the spark plug (Figure 24). Procedures Preparing the Machine for Maintenance... -
Page 18: Engine Maintenance
Engine Maintenance 9. Wipe dirt from the base and the cover with a moist rag. Note: Be careful to prevent dirt and debris from entering the air duct leading to the carburetor. Servicing the Air Cleaner 10. Install the foam elements and ensure that it is properly Service Interval: Before each use or daily—Inspect the air positioned. -
Page 19: Changing The Engine Oil
(Figure 26). 40°C G019298 Figure 27 1. Oil viscosity range for ambient operating temperatures Note: Toro Premium Engine Oil is available from your Authorized Toro Dealer. 1. Remove the oil cap/dipstick (Figure 28). g021483 Figure 26 6. -
Page 20: Servicing The Spark Plug
Checking the Spark Plug 2. Slowly pour approximately 80% of the specified amount of oil into the fill port (Figure 28). Note: Use a gapping tool/feeler gauge to check and adjust 3. Add additional oil to bring the oil level to the proper the air gap. - Page 21 • When installing an in-service spark plug, tighten the plug an additional 1/8 to 1/4 turn. • When installing a new spark plug, tighten the plug an additional 1/2 turn. 4. Install the spark-plug wire pushing the wire onto the terminal of the plug (Figure 29).
-
Page 22: Fuel System Maintenance
Fuel System Maintenance Servicing the Fuel System Cleaning the fuel filter Service Interval: Every 100 hours/Yearly (whichever comes first)—Clean the fuel filter. Inside the fuel tank is a fuel filter to catch dirt in the fuel. 1. Turn off the engine; refer to Stopping the Engine (page 14) and place the machine in the resting position (Figure 14). -
Page 23: Cleaning
Cleaning Storage Important: You can wash the machine with mild Cleaning the Machine detergent and water. Do not pressure wash the engine. 1. Remove concrete, sand, and aggregate from the Regular cleaning and washing will increase the life span of external parts of the machine, especially the engine. -
Page 24: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The engine will not start. 1. The fuel-valve lever is in the Off 1. Move the fuel-valve lever to the On position. position. 2. The choke is closed. 2. Open the choke when starting a hot engine. - Page 25 Notes:...
- Page 26 Notes:...
- Page 27 Notes:...
- Page 28 Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company. Australian Consumer Law: Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.