Page 1
AZG-1 English SERVICE MANUAL CD MECHANISM BASIC CD MECHANISM:KSM-2131FAM TYPE BASIC CD MECHANISM ZD4RDC2 KSM-2131 FAM S/M Code No. 09-001-335-3NJ...
Page 2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
Page 3
Precaution to replace Optical block (KSS-213F) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure.
Page 4
How to Adjust the Rotating Phase of the Gear, Main Cam 1) Push down the hooking catch of the CHAS. MECH, and remove the TRAY. 2) Align the arrow mark of the Gear, Main Cam with the black round mark of the CHAS, MECHA as shown below. 3) Confirm that the Slide, Mech Cam is located in the right position, then insert the TRAY gently.
Page 5
ELECTRICAL MAIN PARTS LIST-1/2 REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION C193 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C201 87-A10-730-080 CAP,E 1000-16 SMG 87-A21-381-040 C-IC,LA9235M C202 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 87-A21-414-010 IC,BA5927S C204 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 87-A21-591-010...
ELECTRICAL MAIN PARTS LIST-2/2 • Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received. CHIP RESISTOR PART CODE Chip Resistor Part Coding Figure Resistor Code Value of resistor...
Page 7
TRANSISTOR ILLUSTRATION-1/1 E C B 2SK2158 DTA114YS 2SA19790/Y 2SA1235F 2SC3052F KTA1266GR DTC124XKA...
Page 8
BLOCK DIAGRAM-1/1 16.934MHz RVDD LC78641NE-D VREF VREF VREF CN701 CN401 LED503,504 KSS-213F MOTOR C.B CD MECHANISM KSM-2131FAM...
Page 12
IC BLOCK DIAGRAM-1/1 IC, BA5927S IC, LA9235M -12-...
Page 13
IC DESCRIPTION-1/1 (LC78641NE-D)-1/3 Pin No. Pin Name Description PDO1 Internal VCO control phase comparator output pin. (Pull down) Internal VCO control phase comparator output pin. PDO2 OFF for rough servo, ON for phase servo. (Pull down) VVSS — Internal VCO ground pin. PCKIST —...
Page 14
IC DESCRIPTION-1/1 (LC78641NE-D)-2/3 Pin No. Pin Name Description EFLG C1, C2 error correction monitor pin. (Not connected) TEST Test input pin. (Connected to GND) Emphasis pin. Which becomes an input pin after reset and can be controlled externally. This EMPH becomes an emphasis monitor pin under control by command.
Page 15
IC DESCRIPTION-1/1 (LC78641NE-D)-3/3 Pin No. Pin Name Description Rough servo/phase control automatic switching monitor output pin. “H” for rough servo and “L” for phase servo. (Not connected) Synchronization signal detection output pin. FSEQ Outputs a high level when the synchronization signal detected from the EFM signal and the internally generated synchronization signal agree.
Page 16
MECHANICAL EXPLODED VIEW-1/1 LED C.B 3CD C.B (ZZJ-J) T-T C.B CUSHION,CD A CUSHION, CD A KSM-2131FAM CUSHION,CD A -16-...
Page 17
MECHANICAL PARTS LIST-1/1 REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION 1 84-ZG1-225-010 BELT,SQ1.0-63.3 21 83-ZG3-604-010 RING,MAG 2 2 84-ZG1-672-010 F-CABLE,5P 1.25 210MM WHITE N 22 83-ZG3-213-010 LVR,SW 3 84-ZG1-216-310 SLIDE,MECHA CAM YEL 23 84-ZG1-208-210 LEVER,CAM 4 84-ZG1-267-010 PULLEY,LOAD MO 8 24 84-ZG1-205-210...
COLOR NAME TABLE Basic color symbol Color Basic color symbol Color Basic color symbol Color Black Cream Orange Green Gray Blue Transparent Blue Gold Pink Silver Titan Silver Brown Violet White Transparent White Yellow Transparent Yellow Metallic Blue Light Blue Transparent Green Dark Blue Transparent Orange...