Symbol CRD 2700-4000E Manual
  1. Manuals
  2. Brands
  3. Symbol Manuals
  4. Conference System
  5. CRD 2700-4000E
  6. Manual
Symbol CRD 2700-4000E Manual

Symbol CRD 2700-4000E Manual

Ethernet cradle
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
C
R
D
2
7
0
0
-
4
0
0
0
E
E
t
h
e
r
n
e
t
C
r
a
d
l
e

Advertisement

Table of Contents
loading

Summary of Contents for Symbol CRD 2700-4000E

  • Page 2 Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.

  • Page 3: Table Of Contents

    Scout or AVANTGO is required. This software may be purchased from Symbol. Contact your Symbol sales representative for information. About This Guide This guide provides instruction on setting up and using the CRD2700-4000E 4-slot Ethernet cradle, as well as setting up an SPT 1700 or PPT 2700 terminal for use with the CRD2700-4000E.

  • Page 4: Set Up

    Save the shipping box for storing or shipping. Connecting Power Note: Use only a Symbol-approved power supply, output rat- ed 8Vdc and minimum 5A. The power supply is certi- fied to EN60950 with SELV outputs.
  • Page 5 Q u i c k R e f e r e n c e Hinweis: Benutzen Sie nur eine Symbol Technologies geneh- migt Stromversorgung in den Ausgabe: 8 Vdc und minimum 5 Ampere. Die Stromversorgung ist bes- cheinigt nach EN60950 mit SELV Ausgaben.

  • Page 6: Setting Up For Network Communications

    C R D 2 7 0 0 - 4 0 0 0 E E t h e r n e t C r a d l e Setting Up for Network Communications The CRD2700-4000E cradle allows communication between terminals and their associated host computers connected to an Ethernet network.
  • Page 7 Q u i c k R e f e r e n c e 2. Connect one end of a standard 10 Base-T network cable to the connector labelled Host on the back of the CRD2700- 4000E. Connect the other end of the cable to a hub which is connected to your subnet.
  • Page 8 C R D 2 7 0 0 - 4 0 0 0 E E t h e r n e t C r a d l e Static Mode If there is no DHCP server on your network, the cradle must be manually configured with IP addresses and other network-related information.
  • Page 9 Q u i c k R e f e r e n c e 5. Type ‘g’ and press Enter to run the EFlasher utility. The fol- lowing screen displays er86mon:g Cradle Utilities Version x.xx I) Flash Info P) Program Cradle Globals Q) Quit 6.
  • Page 10 C R D 2 7 0 0 - 4 0 0 0 E E t h e r n e t C r a d l e uses a DHCP server, this IP address must be reserved for this CRD2700-4000E. See your network administrator for assistance.
  • Page 11 Q u i c k R e f e r e n c e 14. Once all values are set correctly, type ‘F’ to write these val- ues into flash memory. The terminal displays the following screen Erasing flash sector at E0000... Cradle Utilities Version x.xx I) Flash Info P) Program Cradle Globals...

  • Page 12: Inter-Connecting Cradles

    C R D 2 7 0 0 - 4 0 0 0 E E t h e r n e t C r a d l e translation is that multiple slots can simultaneously share the one network IP address of the cradle. Accessing the outside network with the CRD2700-4000E is not the same as a direct connection to the outside network.

  • Page 13: Software Configuration

    Q u i c k R e f e r e n c e 2. Plug one end of the inter-cradle cable into the Expansion Connector modular jack labeled EXP on the back of the first cradle. Ethernet Cradle Serial Cradle Inter-Cradle Cable 3.
  • Page 14 C R D 2 7 0 0 - 4 0 0 0 E E t h e r n e t C r a d l e a. Select the HotSync application from the main application screen. b. Select the menu icon to display the options menu. c.
  • Page 15 Q u i c k R e f e r e n c e d. Check any items that you want synchronized and un- check any items that you don’t want synchronized, then tap OK. 4. To configure the Connection Setup: a.
  • Page 16 PC. If the application requires simultaneous connection to a single host database, additional software, available from Symbol, is required. Terminals inserted into daisy-chained cradles are HotSync’d in a round-robin fashion simultaneously with any HotSyncs from local slots.

  • Page 17: Configuring The Ppt 2700

    Q u i c k R e f e r e n c e terminal are communicating. Removing the terminal from the cradle while the LED is flashing green disrupts communication and data may be lost.If the terminal is inserted into an inter-connected serial cradle slot while another terminal on the serial cradle chain is communicating with a host, the terminal waits (its LED remains red) until the first terminal finishes communicating, then the slot’s...
  • Page 18 C R D 2 7 0 0 - 4 0 0 0 E E t h e r n e t C r a d l e 2. From ActiveSync, select the File menu and the Connection settings item. 3. In the Connection settings dialog box, check the Allow Network and Remote Access Service (RAS) server con- nection with this computer option.

  • Page 19: Battery Charging

    Q u i c k R e f e r e n c e Configuring eConnect To configure eConnect: 1. Tap Start. 2. Tap Settings 3. Select the System tab. 4. Select the eConnect applet. 5. Select the Automatically detect connections option if you’d like the terminal to detect when it is inserted in the cra- dle.

  • Page 20: Indicator Lights

    C R D 2 7 0 0 - 4 0 0 0 E E t h e r n e t C r a d l e Indicator Lights Light Indication No terminal is present in the slot. Solid Red Terminal is present, but communication has not started.
  • Page 21 Q u i c k R e f e r e n c e Symptom Cause Suggested Action Attempt by the Terminal was re- Replace the terminal in the cradle. cradle to HotSync moved from the cra- This allows the cradle to attempt the terminal failed.
  • Page 22 C R D 2 7 0 0 - 4 0 0 0 E E t h e r n e t C r a d l e Radio Frequency Interference Requirements - Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la Classe A est conforme à...
  • Page 23 Customer will pay for the replacement product in case it does not return the replaced product to Symbol within 3 days of receipt of the replacement product. The process for return and customer’s charges will be in accordance with Symbol’s Exchange Policy in effect at the time of the exchange.
  • Page 24 9-1-320-39-09 Sweden 84452900 Latin America Sales Support 1-800-347-0178 Inside US +1-561-483-1275 Outside US Europe/Mid-East Distributor Operations Contact local distributor or call +44 208 945 7360 72-50357-01 Revision A — January 2001 Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300...

Table of Contents