Advertisement
Quick Links
™
Play Dome
Product features may vary from picture above.
Model Number: B0003
Please keep this instruction sheet for future reference, as it contains important information.
Tool needed for assembly: Phillips Screwdriver (not included).
Use only for a child who is unable to push up on hands and knees, pull up or sit unassisted.
Advertisement
Related Manuals for Fisher-Price LEARNING PATTERNS Play Dome
Summary of Contents for Fisher-Price LEARNING PATTERNS Play Dome
- Page 1 ™ Play Dome Product features may vary from picture above. Model Number: B0003 Please keep this instruction sheet for future reference, as it contains important information. Tool needed for assembly: Phillips Screwdriver (not included). Use only for a child who is unable to push up on hands and knees, pull up or sit unassisted.
- Page 2 Failure to follow these warnings or send you replacement parts. and instructions could result in Please call Fisher-Price® Consumer Relations, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday. serious injury or death. Hearing-impaired consumers using TTY/TDD equipment, To reduce the risk of Sudden Infant please call 1-800-382-7470.
-
Page 3: Table Of Contents
Parts Metal Stay 2 Covers 3 Toys (Toys may be different than shown.) 2 Base Wires Base Plastic Stay M4 x 1 " Screw - 2 M4 Lock Nut - 2 (Inside Base Frames) Spring - 4 M5 x 1 "... - Page 4 IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or Canopy Tunnel broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Metal Stay...
- Page 5 Assembly Frame with Lock Nuts Frame Tube Frame Tube • Tighten the screws with a Phillips screwdriver. Do not M5 x 1 " Screw - 4 over-tighten. • Repeat assembly steps 3 - 5 to attach the other ends of Rounded the frame tubes to the frame on the other side of the base.
-
Page 6: Spring
Assembly Frame with Lock Nuts Frame Frame Lower Hole Lower Hole Base Wire Spring Spring Base Wire M5 x 1 " Screw - 4 • Tighten the screws with a Phillips screwdriver. Do not Rounded over-tighten. Side • Repeat this procedure to attach the other ends of the base wires to the frame with lock nuts on the other side M5 Lock Nut (Inside Frame) - 4 of the base. -
Page 7: M4 X 1
Assembly • Tighten the screw with a Phillips screwdriver. Do not over-tighten. • Repeat this procedure to attach the other end of the metal Metal Stay canopy stay and the remaining cover to the frame on the other side of the base. Cover Upper Hole... - Page 8 Set-Up & Use To Unfold PUSH PUSH Frame Groove Base Wire Sides of Base Wire • Position the product upright on a flat surface. • Grasp both sides of a base wire. Pull both sides of the base wire outward and then let the base wire rotate down. Note: If the base wire does not freely rotate down, pull the sides of the base wire further outward.
- Page 9 Set-Up & Use Using the Canopy Using the Mesh Cover Canopy Up Zipper Canopy Down Mesh Cover Up Canopy Up • Adjust the canopy up or down. • Adjust the canopy and mesh cover up. • While holding the mesh cover up, fasten the zipper closed.
- Page 10 Set-Up & Use Canopy Strap Strap • Fit a strap inside the dome through the slot in the toy ring. Fasten the strap. • Or, attach the toys to the straps on the canopy (see step 6). • Fit the canopy strap through the slot in the toy ring.
- Page 11 Set-Up & Use To Fold for Portability Frame Base Wire Groove Groove Sides of Base Wire • Rotate the base wire up. • Grasp both sides of a base wire. • Repeat this procedure to fold the other base wire. •...
- Page 12 Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2002 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.