Table of Contents
Advertisement
This gas fireplace should be installed by a qualified
installer in accordance with local building codes and with
current CSA-B149 (.1 or .2) Installation codes for Gas
Burning Appliances and Equipment. For USA Installations
follow local codes and/or the current National Fuel Gas
Code. ANSI Z223.1. If the unit is being installed in a
mobile home the installation should comply with the
current CAN/USA Z240.4 Code.
FOR SAFE INSTALLATION AND OPERATION PLEASE
NOTE THE FOLLOWING:
1 . This fireplace gives off high temperatures and should
be located out of high traffic areas and away from
furniture and draperies.
2. Children and adults should be alerted to the hazards
of fireplace high surface temperatures and should
stay away to avoid burns or ignition of clothing.
3. CAUTION: Due to high glass surface temperature
children should be carefully supervised when in
the same room as fireplace.
4. Under no circumstances should this fireplace be
modified. Parts removed for servicing should be
replaced prior to operating this fireplace again.
5. Installation and any repairs to fireplace must be
performed by qualified installer, service agency or gas
supplier. A professional service person should be
contacted to inspect fireplace annually. More frequent
cleaning may be required due to excess lint and dust
from carpeting, bedding material, etc.
6. Control compartments, burners and air passages in
this fireplace should be kept clean and free of dust
and lint. Make sure that the gas valve and pilot light
are turned off before you attempt to clean this
fireplace.
7. The venting system (chimney) of this fireplace should
be checked at least once a year and if needed your
venting system should be cleaned.
8. Keep the area around your fireplace clear of combusti-
ble materials, gasoline and other flammable vapour
and liquids. This fireplace should not be used as a
drying rack for clothing, nor should Christmas stockings
or decorations be hung on or around the fireplace.
9. Under no circumstances should any solid fuels (wood,
coal, paper or cardboard etc.) be used in this
fireplace.
10. The flow of combustion and ventilation air must not be
obstructed in any way.
11. When the fireplace is installed directly on carpeting,
vinyl tile or any combustible material other than wood,
this fireplace must be installed on a metal or wood panel
extending the full width and depth of the fireplace.
12. This fireplace requires adequate ventilation and
combustion air to operate properly.
13. This fireplace must not be connected to a chimney flue
serving a separate solid fuel burning fireplace.
14. When the fireplace is not in use it is recommended
that the gas control valve be left in the OFF position.
10004000
INSTALLATION & OPERATING INSTRUCTIONS
IMPORTANT:
PLEASE REVIEW THE FOLLOWING CAREFULLY
Remove any plastic from parts before turning the
fireplace ON.
It is normal for fireplaces fabricated of steel to give
off some expansion and/or contraction noises
during the start up or cool down cycle. Similar
noises are found with your furnace heat exchanger
or car engine. It is not unusual for your gas fireplace
to give off some odor the first time it is burned. This
is due to the curing of the paint and any undetected
oil from the manufacturing process.
Please ensure that your room is well ventilated-
open all windows.
It is recommended that you burn your fireplace for
at least ten (10) hours the first time you use it. If the
optional fan kit has been installed, place the fan
switch in the "OFF" position during this time.
LOCATING YOUR FIREPLACE
12" (305mm)
A
12" (305mm)
B
E
A - *Flat on wall
B - *Room divider
D - Cross corner
E - Flat on wall corner
* A & B must maintain a 12" (305 mm) clearance between the wall and
side glass of fireplace.
There is a minimum vertical rise required for the
venting which varies depending on the application.
The maximum horizontal run also has restrictions.
Become familiar with the venting instructions starting
on page 9, before starting the installation.
CLEARANCE TO COMBUSTIBLES
Adequate clearances as listed below must be main-
tained for servicing and proper operation.
Back.................................... 0"
Side..................................... 12"
Floor.................................... 0"
Top...................................... 36"
Corner................................ 0" to Back Edges
Vent Pipe............................ 1"
Irving Oil
D
C
F
Fig. 1
C - Island
3
Advertisement
Table of Contents
Troubleshooting
