Telephone Mute; Brightness Control; Illumination Colour; Security Led - VDO CD 2217 G User Manual

Telephone Mute

This headunit was designed to interface with dif-
ferent types of hands-free kits that provide tel-
ephone mute cables. Please read the instruction
manual of your hands-free kit on its mute logic
level (either mute-high or mute-low).
1. Navigate the SAM to select 'TEL MUTE'.
2. Turn the knob clockwise / anti-clockwise
to toggle the logic level according to your
hands-free kit type.
Note: In the case that your headunit always
remains in 'TEL MUTE' mode, that is, sound
is muted, you can try to reverse the logic level
(e.g. from 'TELM HI' to 'TELM LO'). If this still
does not work, perhaps your hands-free kit is
not compatible with this headunit and it is best to
turn the 'TEL MUTE' function to 'TELM OFF'.

Brightness Control

This headunit comes with two levels of bright-
ness level. To adjust the brightness:
1. Navigate the SAM to select 'BRIGHTNESS'.
2. Turn the knob clockwise / anti-clockwise to
select the brightness level.

Illumination Colour

To allow best integration into your car dash-
board, the headunit comes with three types
of colours scheme, namely Orange, Green or
Mixed of Orange and Green. To change the
illumination colour:
1. Navigate the SAM to select 'COLOR'.
2. Turn the knob clockwise / anti-clockwise to
select the colour scheme.

Security LED

The blinking security LED can deter potential
theft of your headunit, even after your front panel
is removed. However, if you wish to save your
battery life, you can turn off this LED.
1. Navigate the SAM to select 'LED'.
2. Turn the knob clockwise / anti-clockwise to
turn on or off the blinking LED.
Speed Dependent Volume Control
(SDVC)
To compensate for surrounding noise, this func-
tion automatically increases the volume of the
headunit with respect to the car's speed. There
are two compensation levels selectable from the
SAM. Level 1 gives a smaller increase (in vol-
ume) and level 2 gives a higher increase.

Calibration

CAUTION: To avoid unnecessary dis-
traction, we advise that this procedure
be carried out with the assistance of
somebody else (front passenger).
1. While the car is stationary, press-and-hold
both and buttons at the same time.
PWR
SOUND
MUTE
2. The headunit will mute and show "RE-CALIB"
and "50 KM/H" alternatively.
3. Within 30 seconds, drive your car to 50 km/h
(about 30 mph).
Important note: Always obey the Highway Code
and the current traffic restrictions and conditions!
4. Once the speed is reached, short-press the
SAM button and you will hear a beep and the
AST
display will show "CALIB OK".
5. Turn off and then turn on your headunit again
and level 1 of the SDVC is automatically
selected.
Note: This headunit's SDVC works on frequen-
cy-based signal (PCM) rather than on width-
based signal (PWM). Some vehicles come with
PWM signals and are therefore not compatible
with this SDVC function.
Steering Wheel Remote Control
(SWRC)
This headunit is specially designed with a pro-
grammable Steering Wheel Remote Control
(SWRC) to suit your car built-in SWRC as much
as possible.
Important note: This function supports SWRCs
that are based on analogue RC3-standard
only. Other SWRCs, especially those based on
CAN-bus, are not supported. For these SWRCs,
please consult your dealer for a suitable con-
verter, if available.
1. While the car is stationary, press-and-hold
both and
PWR
MUTE
SOURCE
2. The headunit will mute and show "PROG
SWRC" for one second.
3. After that, the headunit will prompt you the
first programmable function, that is, "VOL-
UME-".
4. Rotate the volume knob clockwise or anti-
clockwise to navigate through the functions.
5. Match a suitable SWRC buttons (e.g. "VOL-"
or "-") with the one of the pre-defined func-
tions that is displayed (e.g. "VOLUME-")
by pressing and holding the corresponding
SWRC button for more than 2 secs.
6. If the headunit recognizes the input as stable,
it will capture the key-press input, give a con-
firmation beep, and will show "PROG OK".
buttons at the same time.
23