1. Manuals
  2. Brands
  3. Smeg Manuals
  4. Dishwasher
  5. 4060 Series
  6. Service manual

Smeg 4060 Series Service Manual

Components disassembly sequence
Hide thumbs
Table of Contents

Advertisement

Quick Links

Disassembly sequence series 4060
COMPONENTS DISASSEMBLY SEQUENCE
SERIES 4060
1

Advertisement

Table of Contents
loading

Related Manuals for Smeg 4060 Series

Summary of Contents for Smeg 4060 Series

  • Page 1 Disassembly sequence series 4060 COMPONENTS DISASSEMBLY SEQUENCE SERIES 4060...

  • Page 2: Table Of Contents

    Disassembly sequence series 4060 TABLE OF CONTENTS Symbols used in the disassembly procedure.…………………………………………………..3 Tools used ……………..……………………………………………………………………..….4 Screws used ……………..…………………………………………………………………..…5 Front panel, lock, display board disassembly…..………………………………………………..6 Main electronic circuit board disassembly…..……………………………………………..……...10 Motor disassembly…..…………………………………………………... ………………………….13 Upper spray arm delivery tube disassembly……………………... ………………………………18 Transducer disassembly…………………………….……………………...

  • Page 3: Symbols Used In The Disassembly Procedure

    REQUIRE THE PRESENCE OF 2 PERSONS OPERATION TO BE CARRIED OUT WITH THE HELP OF SUITABLE GLOVES Caution! maintenance and any repairs must be performed by Smeg authorized service technician! Warning! For any replacement an original Smeg spare part must be used.

  • Page 4: Tools Used

    Disassembly sequence series 4060 TOOLS USED TOOL No. 1 Phillips slotted screwdriver TOOL No. 2 Long nose pliers TOOL No. 3 13mm Open-ended spanner TOOL No. 4 Box spanner 7mm TOOL NO. 5 ELECTRIC IMPACT WRENCH TOOL No. 6 flat-blade screwdriver AND/OR SCREWDRIVER WITH INSERT FOR CROSS-HEAD SCREW TOOL No.

  • Page 5: Screws Used

    Disassembly sequence series 4060 SCREWS USED Caution! the machine requires different screws which must not be mixed! Screws with knurled head : for Screws with smooth head (steel): for fastening components on the back of fastening the front components, the machine : inside the machine...

  • Page 6: Front Panel, Lock, Display Board Disassembly

    Disassembly sequence series 4060 DISASSEMBLY: 1) FRONT PANEL, 2) DOOR LOCK 2) DISPLAY ELECTRONIC BOARD Tools required in this disassembly procedure TOOL No. 1 Phillips slotted screwdriver Before any maintenance and repair of the equipment, electrically disconnect the machine. MACHINE FULL VIEW 1.Open the door of the appliance.
  • Page 7 Disassembly sequence series 4060 1-front panel disassembly 1. Remove the 6 screws that secure the front 2.Now it is possible to remove the front panel panel to the door (tool no.1) paying attention to the electrical connections. 3. View of components inside the front panel. 4.Disconnect cable that...
  • Page 8 Disassembly sequence series 4060 2-door lock disassembly After removing the front panel, according to the above procedure, continue disassembling the door lock. 1.Remove the two screws that secure the lock to DETAIL OF LOCK REMOVED the door ( tool n.1)
  • Page 9 Disassembly sequence series 4060 3-display board disassembly After removing the front panel, according to the above procedure, continue disassembling the display board. 1. Remove the two screws that secure the display 2. Now it is possible to remove the display board board unit to the front panel (tool no.

  • Page 10: Main Electronic Circuit Board Disassembly

    Disassembly sequence series 4060 MAIN ELECTRONIC BOARD DISASSEMBLY Tools required in this disassembly procedure TOOL No. 1 Phillips slotted screwdriver 1.Open the door and remove the 6 screws that secure the front panel (tool no. 1). 2. Now it is possible to remove the front panel 3.Detail of the main electronic board.
  • Page 11 Disassembly sequence series 4060 4.Remove the two screws that secure the shell + 5. Disconnect the electronic board power electronic board (tool no.1) supply cable. 6. Now it is possible to remove the electronic board from its housing.
  • Page 12 Disassembly sequence series 4060 Warning! before disconnecting the probe connectors, identify them according to the indications (TL/TC/TA)! Be careful when re-connecting the TL/TC/TA connectors (respectively: washing temperature/control temperature/drying temperature) as silkscreen printed on the board! Warning! for proper connection of the connectors, match the silkscreen printing both on the electronic board and on the connector to be connected...

  • Page 13: Motor Disassembly

    Disassembly sequence series 4060 WASHING MOTOR DISASSEMBLY Tools required in this disassembly procedure TOOL No. 1 Phillips slotted screwdriver TOOL No. 2 Long nose pliers 1- Remove the top secured by two screws on the rear 2.Now pressing with the hand on the front top (1), side of the machine (tool no.
  • Page 14 Disassembly sequence series 4060 Front view, place the machine on its left side, taking care not to damage it. APPLIANCE REAR SIDE 5. Now operate on the rear side of the machine. Remove the screws indicated to disassemble the lower rear crossbar.
  • Page 15 Disassembly sequence series 4060 7.Disconnect the capacitor drain tube. 6.Loosen the cable gland of the power cord. 8.Release the pressure switch from the lower rear crossbar. (Tool no. 2). Now it is possible to completely remove the lower crossbar.
  • Page 16 Disassembly sequence series 4060 10. Disconnect the tubes shown. APPLIANCE BASE VIEW 11. Now operate from the base of the dishwasher. 12. Remove the base protection forward, to remove it completely. Remove the 3 screws that secure the base protection of the appliance.
  • Page 17 Disassembly sequence series 4060 13. Using tool no. 7, remove the 6 screws that 14. Disconnect the pressure switch connecting tube secure the washing motor to the related support and the electrical connections. bracket. Dishwasher bottom MOTOR REMOVED 15.Remove the motor from the housing.

  • Page 18: Upper Spray Arm Delivery Tube Disassembly

    Disassembly sequence series 4060 UPPER ARM SPRAYER DELIVERY TUBE DISASSEMBLY Tools required in this disassembly procedure TOOL No. 1 Phillips slotted screwdriver TOOL No. 2 Long nose pliers TOOL No. 3 13mm Open-ended spanner TOOL No. 6 flat-blade screwdriver 1- Remove the top, secured by means of two 2.Now pressing with the hand on the front top (1), screws on the rear side of the machine (tool no.
  • Page 19 Disassembly sequence series 4060 3.Remove the 3 front screws that secure the left side (tool no.1). APPLIANCE BASE VIEW Retention tooth 4.Using tool no. 6, press on the retention tooth that secures the side of the machine, in order to access the lateral components.
  • Page 20 Disassembly sequence series 4060 APPLIANCE BASE VIEW 6. Remove the base protection forward, to remove it completely. Place the unit on its back, taking care not to damage it. Remove the 3 screws that secure the base protection of the appliance. (tool no.1) 7.
  • Page 21 Disassembly sequence series 4060 8.Remove the electrical connections to 9. Remove the clamp that fastens the upper spray completely release the capacitor. arm delivery tube. 10.Open the dishwasher door and remove the 11. Now it is possible to remove the duct from the upper spray arm top of the appliance and ..
  • Page 22 Disassembly sequence series 4060 12..by slightly moving the left side (front Warning! the tightening of the clamp that view) completely remove the component. secures the spray arms duct, must not be positioned at the stroke end!

  • Page 23: Transducer Disassembly

    Disassembly sequence series 4060 TRANSDUCER DISASSEMBLY Tools required in this disassembly procedure TOOL No. 1 Phillips slotted screwdriver TOOL No. 2 Long nose pliers GLOVES 1- Remove the skirting board. 2 Remove the two screws that secure the components protection (tool no. 1) 3.
  • Page 24 Disassembly sequence series 4060 housing. 5.Remove the connector for electrical 6.Now it is possible to fully release the connection. component from it housing.

  • Page 25: Air Trap Disassembly

    Disassembly sequence series 4060 AIR TRAP DISASSEMBLY Tools required in this disassembly procedure TOOL No. 1 Phillips slotted screwdriver TOOL No. 2 Long nose pliers 1- Remove the skirting board. 2 Remove the two screws that secure the components protection (tool no. 1)
  • Page 26 Disassembly sequence series 4060 APPLIANCE BASE VIEW 4. Remove the 3 screws that secure the base Front view. Place the machine on the protection of the appliance (tool no. 1). left side, taking care not to damage the appliance. 6. Disconnect the tube that connects the air trap 5.
  • Page 27 Disassembly sequence series 4060 7. Set the machine upright and remove the lower 8.Remove the filter by turning it counterclockwise. spray arm. 9. Remove the drain compartment cover secured by 10. Grasp the air trap, rotate clockwise (1) and means of 4 screws (tool no. 1). then push the component (2) towards the machine back to remove it completely from the seat.
  • Page 28 Disassembly sequence series 4060 gasket WARNING! every time the air trap is Warning! after assembling the new air changed, it is recommended to replace also the trap spare part, put back the clamp that secures black gasket! the tube to the air trap as before, to prevent any leaks!

Table of Contents