Maintenance And Storage; Snow Throwing Tips - IVT SNWB-252-RC Instruction Manual

Instruction manual
2. Place a spacer board on the ground underneath
the auger shave plate between the skid shoes (8). The
thickness of the board should be the same as the height
above the ground you wish to raise the auger shave
EN
plate to. The skid shoes (8) should not touch the board.
3. Using a wrench, loosen the two nuts located on
each skid shoe (8) and allow the skid shoes (8) to slide
to the ground.
4. Re-tighten the nuts on the skid shoes (8) and wheel
your machine off of the spacer board.
Driving and auger (9) operation
1. Press down on the auger control (3) on the left-
hand side. The auger (9) should start spinning.
2. Press down on the drive control (1) on the right-
hand side. The machine should start moving in the
direction with the speed set by the shift lever (2).
3. When finished clearing a snow path, release the
auger control (3) and the drive control (1).
4. The drive speed can be adjusted by using the drive
shift lever (2). Be sure to release both the auger control
(3) and the drive control (1) before adjusting the shift
lever (2).
WARNING! Never change the speed
while your machine is moving. It could
damage the drive mechanism and void
the warranty.
Chute outlet direction adjustment
The angle of the chute deflector (7) controls the throwing
distance of the snow leaving the chute. Raising the
angle will increase the throwing distance.
Lowering the angle will decrease the throwing distance.
1. Make sure the drive control (1) and auger control
(3) are released. The auger (9) has to come to a full
stop.
2. Loosen the knobs on the chute deflector (7) and
adjust the chute deflector (7) to the desired angle.Then
retighten the knobs on the chute deflector (7). Do not
over-tighten.

SNOW THROWING TIPS

∙ Always operate the machine with the engine (5) at
full throttle. Full throttle offers the best performance.
∙
Go slower in deep, freezing or heavy wet snow.
Use the shift lever (2), not the throttle, to adjust speed.
∙
It is easier and more efficient to remove snow
immediately after it falls.
∙ The best time to remove snow is the early morning.
At this time the snow is usually dry and has not been
exposed to the direct sun and warming temperatures.
∙
Slightly overlap each successive path to ensure all
snow will be removed.
∙
Throw snow downwind whenever possible.
∙ Adjust the skid shoes (8) to proper height for current
snow conditions. For extremely heavy snow, reduce the
width of snow removal by overlapping previous path and
moving slowly.
∙
Keep engine (5) clean and clear of snow during
use. This will help air flow and extend engine (5) life.
WARNING! Do not operate machine if
weather conditions impair visibility.
Throwing snow during a heavy, windy
snowstorm can blind you and be
hazardous to the safe operation of the
machine.

MAINTENANCE AND STORAGE

CAUTION! Before carrying out any
maintenance
the engine and wait until it stops
completely.
∙
Always keep the tool and the ventilation slots (if
present) cleaned. Regular cleaning and maintenance of
the appliance will ensure efficiency and prolong the life
of your tool.
∙ If the tool should fail despite the rigorous
manufacturing and testing procedures, the repair should
be carried out by an authorized IVT customer service.
∙
Keep all nuts, bolts, and screws tight, to be sure the
tool is in safe working condition.
∙ Replace worn or damaged parts for safety.
∙
Use only original spare parts. Parts not produced
by manufacturer may cause poor fit and possible injury.
∙ Store the tool in a dry room out of reach of kids and
away from any flammable material.
∙ Store all fuel tanks securely. Never store the
equipment with fuel in the tank inside a building, where
fumes can reach an open flame or sparks.
IMPORTANT! Keep all grease and oil off of the
rubber friction wheel and aluminum drive plate.
Shave plate and skid shoe (8)
The shave plate and skid shoe (8) on the bottom of
the snow blower are subject to wear. They should be
checked periodically and replaced when necessary.
To remove skid shoe (8):
∙ Remove the carriage bolts and hex flange nuts.
∙
Reassemble new skid shoes (8) with the carriage
bolts and hex flange nuts.
12
operation, turn off