Download Print this page

nekos MR28-B Instruction Manual

Tubular gearmotor for blinds - 28mm, electrical feeding 24v

Advertisement

Quick Links

MR28-B
INSTRUCTION MANUAL
INSTRUCTION MANUAL
EN
TUBULAR GEARMOTOR FOR BLINDS – Ø28MM
TUBULAR GEARMOTOR FOR BLINDS
TUBULAR GEARMOTOR FOR BLINDS
Electrical feeding
trical feeding 24V
NEKOS S.r.l. - Via Capitoni, 7/5
Via Capitoni, 7/5 - 36064 Colceresa (VI) –
+39 0424 411011 –  +39 0424 411013 - www.nekos.it -
+39 0424 411011
4420003 – Rev. 2003
– ITALY
info@nekos.it
USER INSTRUCTIONS
CAUTION. Carefully observe all the following installation
instructions to ensure personal safety.
The device is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lacking
experience and knowledge. Do not allow children to play with the
fixed controls and keep any remote-control units out of their
reach.
Have installation checks performed periodically by qualified
personnel from a service centre authorised by the manufacturer.
Do not use if repair or adjustment is required.
CAUTION: if the power cable is damaged, it must be replaced by
qualified personnel from a service centre authorised by the
manufacturer.
CAUTION. Disconnect the power supply during cleaning or
maintenance operations. Do not use solvents or jets of water to
wash the appliance; the appliance should not be submerged in
water.
In the event of fault or malfunction, switch off the device at the
main switch. All repairs and adjustments (e.g. setting the stroke)
must only be performed by qualified personnel from a service
centre authorised by the manufacturer.
Always request exclusive use of original spare parts. Failure to
respect this condition could compromise safety and invalidate
the benefits contained in the warranty for the appliance. In the
event of any problems or queries, consult your agent or contact
the manufacturer directly.
The A-weighted sound pressure level is less than 70dB(A).
Carefully preserve these instructions after installation.
2

Advertisement

loading

Summary of Contents for nekos MR28-B

  • Page 1 Carefully preserve these instructions after installation. NEKOS S.r.l. - Via Capitoni, 7/5 Via Capitoni, 7/5 - 36064 Colceresa (VI) – – ITALY +39 0424 411011 +39 0424 411011 –  +39 0424 411013 - www.nekos.it - info@nekos.it 4420003 – Rev. 2003...
  • Page 2: Table Of Contents

    MANDATORY RISK ANALY MANDATORY RISK ANALYSIS AND PROTECTION MEASURES nekos products have been manufactured in accordance with safety standards and products have been manufactured in accordance with safety standards and products have been manufactured in accordance with safety standards and...
  • Page 3: Technical Data

    The MR28-B gear motors have CE marking and comply with the Standards listed in the have CE marking and comply with the Standards listed in the have CE marking and comply with the Standards listed in the...
  • Page 4: Assembly

    180° to one another with Ø2.5 mm and 10 mm deep. The cable furnished with the MR28-B tubular gear motor is 2 m long and has been calculated in accordance with safety rules. In the event that the distance between the gear motor and feeder should exceed this length, the cable should be extended.
  • Page 5: 10. Troubleshooting

    6. Insert the plug into its position (see figure to the side). Now the programming is finished. 7. Perform a complete stroke up and down of the blind and check that it stops in the desired position. In this case the LED should remain steady-on during the entire control phase.
  • Page 6 Questa dichiarazione è fatta dal costruttore / This is declared by the manufacturer: NEKOS S.r.l. - Via Capitoni 7/5- 36064 Colceresa (Vicenza) - Italy Rappresentato da / Represented by: Giuliano Galliazzo – A.D. Presidente / President CEO...