Page 1
PSC RF Multi SR 12 Pack “Single Band” Frequency Range: 470Mhz to 700Mhz • Supports up to 6 Slot Receivers • Provides RF Distribution • Provides Remote Antenna Power • Smart Battery Slot for Rechargable Operation • Built in Power Management/Charging Circuitry •...
Page 2
Thank you for purchasing your new PSC RF Multi 12 Pack. This device combines a convenient way to mount and house up to six RF Slot Receivers in a compact and rugged portable housing. The PSC RF 12 Pack also provides RF distribution, remote antenna powering, RF flow though, and power distribution to allow powering of your other equipment.
Page 13 Product Description: The PSC RF Multi SR 12 Pack contains two separate, active 1 x 8 RF splitters for use with up to six slot style receivers. This compact, rugged device was developed using the latest super low noise RF amplifiers and will operate over an extended frequency range of 470Mhz to 700Mhz.
Panel Views: Left Side Panel showing: 2 x DB-25 Audio Output Connectors 12x TA3M Audio Output Connections 2 x SMA RF Outputs (loop throughs) Page 2...
Page 6
Right Side Panel Showing: 5 x Power Outputs Dual USB Power Port XLR-4-Male External Power Aaton Digital (Hyrda) USB Port Smart Battery Slot Page 3...
Powering, Internal Battery: The PSC RF 12 Pack is designed to be powered from most any 98 or 99 Watt hour “Smart” Battery. These smart batteries are made by various companies such RRC and Audioroot or Inspired Energy. The Smart Battery is held in place with a stainless-steel spring clip. To remove the Smart battery, simply pull the battery clip toward the front of the RF 12 Pack and slide the battery out.
RF Circuitry: The PSC RF 12 Pack is equipped with two complete RF chains for proper diversity RF feeds to your slot receivers. The two RF chains are labeled “A” and “B”. Each RF chain contains a Bias T Circuit used to allow DC voltage to be send out of the external antenna inputs for use with powered antennas or remote RF amplifiers.
DB-25 connector on receivers. Depending on brand, you may also need to use a machined adapter plate to allow the receiver to sit at the proper depth in the PSC RF 12 Pack. These include: Lectrosonics SRB requires their SRUNI kit.
Smart battery Fuel Gauge. This fuel gauge will light up when the unit is powered up and when there is a smart battery installed and or if the PSC AC power supply is connected and powered up.
Page 7 Audio Outputs, DB-25 Snake Connection: The PSC RF 12 Pack is also equipped with 2 x DB-25 multi-channel audio snake cable connectors. These DB-25 connectors are wired to ADAT wiring standards as listed below: These DB-25 connectors are wired in parallel to the mini XLR connectors.
Photo above shows the four (4) locations of the mounting screws The PSC RF Multi SR 12 Pack is also equipped with four threaded mounting holes on both the top and bottom panels. These threaded mounting holes are compatible with 6-32 screws. The screw threaded inserts are a “blind”...
Page 13
Photo above shows mounting points for use with Sound Devices 688 The PSC RF 12 Pack has two mounting holes designed to allow it to be screwed onto a Sound Devices 688. These two mounting points are shown in the photo above where the blue arrows...
Page 10 SPECIFICATIONS: 13” x 6.5” x 3.3” (33cm x 16.5cm 8.3cm) SIZE: WEIGHT: 4 Lbs (1.8Kg) HOUSING MATERIAL: Aircraft Aluminum HOUSING FINISH: Black Anodize Type II, Black Powder Coating EXTERNAL POWER, NO BATTERY CHARGING: 12-16Vdc, 1.4 Amps nominal, 8 Amps Maximum Pin 1 = Ground, Pin 4 = +12 to +16Vdc EXTERNAL POWER, FOR BATTERY CHARGING:...
Page 15
LIMITED WARRANTY CERTIFICATE: Professional Sound Corporation warrants the PSC RF Multi SR 12 Pack to be free of defective material and workmanship for a period of one year from the original date of purchase and agrees to repair or replace such defective parts or the whole product at its option, provided that the equipment is returned to Professional Sound Corporation.
Page 16
DECLARATION OF CONFORMITY EMC: This product is in compliance with the Electromagnetic Compatibility Directive, 89/336/EEC as defined in EN 50081-1, EN55022 and EN 50082-1. IEC801-2, IEC801-3 and IEC801-4. LVD: This product is in compliance with the requirements of the Low Voltage Directive, 73/23/EEC.