Lorex U222A Series Quick Start Manual

Package Contents
* Per camera in multi-camera packs
• HD Wire-Free Security Camera(s)
• Camera Mounting Kit*
• Rechargeable Power Pack*
• Camera Antenna*
• Allen Key
• Power Pack Adapter
Safety Precautions
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with care.
• Use the camera within given temperature, humidity and voltage levels
noted in the camera's specifications.
• Do not disassemble the camera.
• Do not point the camera directly towards the sun or a source of intense
light.
• Use only the supplied regulated power supply provided with the product
or compatible accessories. Use of a non-regulated, non-conforming
power supply can damage the product and void the warranty.
• Periodic cleaning may be required. Use a damp cloth only. Do not use any
harsh, chemical-based cleaners.
Available Accessories
The following accessories are available for purchase. Visit
search for the model numbers below for details:
Extra Power 2-cell
Accessory
COLOR Pack Power Accessory
Power Pack
Adapters Power Pack
WHITE ACPWF1 ACBATTR2 ACBATTR3
Copyright © 2020 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to
modify product design, specifications and prices, without notice and without incurring
any obligation. E&OE. All rights reserved.
Optimizing Motion Detection
Customize motion detection settings to ensure motion events are being
recorded and reduce false alarms.
To optimize motion detection:
1. Launch the Lorex Cirrus app.
2. Tap a channel in Live View
to select it.
3. Tap , then tap Motion.
4. Configure the following as
needed:
a. Sensitivity: The amount of
motion needed to trigger
recording (e.g., higher
sensitivity requires less motion
to trigger recording).
b. Detection: Enable/disable
motion detection or person
detection per channel.
c. Area Selection: Configure the active area for motion detection so that only areas of
interest are selected and detected.
d. Distance Setting: Configure distance setting for motion detection. While watching the
camera's video on your mobile device, recreate a motion event in front of your camera.
The icon will change from
the distance setting if motion detection is being triggered by unwanted events.
NOTE: Distance will be affected by temperature.
e. Buzzer: Set the recorder to sound an alarm when motion is detected.
lorex.com and
5. Tap Save. Repeat for other cameras on the system.
3-cell Installation Tips
Solar
Follow the tips below for more accurate motion detection and to optimize
Panel
PLUS battery life:
• See images to the right for ideal setup. It is
recommended to place your camera at least 7ft (2.1m)
ACSOL1B
above the ground and angle it slightly downward toward
the monitoring area, excluding any busy areas (e.g.,
sidewalks or roadways).
• Ensure the camera image is free of obstructions (e.g.,
tree branches).
• Position the camera no more than 20ft (6.1m) away
from the area you wish to monitor.
• See the "Optimizing Motion Detection" section to
customize motion settings for each camera on your
system.
• For best performance, position the camera so that
objects of interest will move from side-to-side across
the camera image, rather than moving towards or away
from the camera.
• Install the camera within range of the recorder (noted in
the camera's specifications).
• Test your camera's connection to the recorder prior to selecting a permanent mounting
location.
• This camera is weather resistant for outdoor use (IP66 rated). Installation in a sheltered
location is recommended.
• Battery life will vary based on temperature, settings and number of events.
Disclaimers
• For a full list of compatible recorders, visit lorex.com/compatibility.
• Not intended for submersion in water. Installation in a sheltered location
recommended.
U222A_QSG_EN_R1
a
b
c
d
e
to when motion is detected by the camera. Change
HD Wire-Free Add-On Camera
Quick Start Guide
English Version 1.0
U222A SERIES
lorex.com