Advertisement
QUICK START GUIDE
Avoid running your model in tall grass or soft sand. These will strain
the power system and could damage the motor. If the model becomes
stuck, do not apply throttle. Free the model before operating it.
The TQ 2.4GHz transmitter has a directional antenna. For maximum range,
hold the transmitter upright and pointed in the direction of the model.
Pointing the transmitter away from the model will reduce radio range.
Transmitter Adjustments
Steering Trim
Slowly turn the steering trim knob to precisely set the steering
neutral point. To adjust, drive the vehicle forward slowly
while "steering" with the trim knob until the vehicle travels in
a straight line with no steering input.
Electronic Speed Control Adjustments
ATTENTION: IF USING A LiPo BATTERY
To prevent over-discharging of LiPo batteries, Low-Voltage
Detection must be switched on. To check the status of your model, turn
it on. If the speed control's LED is green, Low-Voltage Detection is
already activated. If the LED is red, Low-Voltage Detection is not active.
Follow these steps to turn on Low-Voltage Detection:
1. Turn the model on. Make sure the LED on the
speed control is on and red.
2. Press and hold the EZ-Set button for ten seconds.
The LED will turn off and then light green, and the
motor will beep twice. Release the button.
3. Low-Voltage Detection is now ACTIVATED.
LiPo batteries are intended only for the most
advanced users that are educated on the risks
associated with LiPo battery use.
To disable Low-Voltage Detection when using NiMH batteries, repeat the
steps above. The motor will beep three times and the LED will glow red.
WARNING: FIRE HAZARD!
Do not use LiPo batteries in this vehicle with
Low-Voltage Detection disabled.
Selecting a Throttle Mode: SPORT, RACE, or TRAINING
1. Connect a fully charged battery to the model and turn on your transmitter.
2. With the model off, press and hold the EZ-Set button until the LED
turns solid green, then solid red, and then begins blinking red. It will
blink once, then twice, then three times, then repeat.
One blink = Sport Mode is the default setting. It allows full forward
and reverse throttle.
Two blinks = Race Mode removes reverse throttle in case your track
does not allow it.
Three blinks = Training Mode will slow the model down by 50% for
young or inexperienced drivers.
3. Release the EZ-Set button after the number of blinks for the mode you
wish to select. Note: If you missed the mode you wanted, keep the EZ-Set
button pressed down and the blink cycle will repeat.
4. The LED will blink and then turn solid green (Low-Voltage Detection
ACTIVE) or red (Low-Voltage Detection DISABLED). The model is now
ready to drive.
Calibrating the Speed Control
The speed control is calibrated at the factory. If the LED on the speed
control is flashing green, then follow these steps to recalibrate it.
1. Connect a fully charged battery to the model.
2. Turn on the transmitter (with the throttle at neutral).
3. Press and hold the EZ-Set button (A).
The LED will first turn green and then
red. Release the EZ-Set button.
4. When the LED blinks RED ONCE, pull
the throttle trigger to the full throttle
position and hold it there (B).
5. When the LED blinks RED TWICE, push
the throttle trigger to the full reverse
and hold it there (C).
6. When the LED blinks GREEN ONCE,
programming is complete. The LED will
then shine green or red (depending on
Low-Voltage Detection setting).
Running in Wet Conditions
Your Traxxas model is designed with water-resistant features to protect
the electronics in the model (receiver, servos, electronic speed control).
Though highly water resistant, the model should not be treated as
though it is submersible or totally, 100% waterproof. Water resistance
applies only to the installed electronic components. Running in wet
conditions requires additional care and maintenance to prevent
corrosion and maintain proper function. Download the complete
manual for full precautions and maintenance requirements. Read
and understand all precautions before operating your model in wet
A
conditions. The complete manual for your model can be viewed and
downloaded by following the link on the cover of this manual or by
scanning the QR code. Please read this entire manual for complete
Red LED: Hold 10 seconds
instructions on the proper use and maintenance of your model.
B
Gearing
Your model may include additional gears. These gears are for maximum-
speed running on hard surfaces only. Using the high-speed gearing for
2 Beeps: LED shines green
general driving and off-road driving may overheat the motor, speed
control, or battery. For full instructions on installing and using the high-
speed gearing, download the complete manual. The complete manual
for your model can be viewed and downloaded by following the link
on the cover of this manual or by scanning the QR code. Please read
this entire manual for complete instructions on the proper use and
maintenance of your model.
After You Run Your Model
Turn the model off
Press and release the EZ-Set button on the speed control.
The speed control's LED will go out.
Unplug the battery and remove it from the model
Do not store the model with the battery installed.
Turn the transmitter off
Always turn the transmitter off last, after the model has been
turned off.
Turn off the model.
1
1
2
2
Unplug the battery.
A
Green then Red
B
Once Red
C
Twice Red
3
3
Always turn your
transmitter off last.
SLASH KIT • 33
Advertisement
