Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Blaupunkt Sevilla CD51
Summary of Contents for Blaupunkt Sevilla CD51
- Page 1 Radio / CD Operating instructions...
- Page 3 button - unlatches the flip/ release panel Volume control Button - switches the radio and mute function on/off RDS button - switches RDS con- venience function on/off (radio data system). Selects variable radio texts. BND button (band), source se- lection for radio mode, selection of FM memory levels and the wavebands MW and LW (Wiesbaden CD51 does not fea-...
-
Page 4: Table Of Contents
Notes and Notes and accessories ... 30 Road safety ... 30 Installation ... 30 Accessories ... 30 International telephone information ... 30 Flip/release panel ... 31 Switching on/off ... 32 Volume adjustment ... 33 Radio mode ... 35 Switching to radio mode ... 35 RDS function (AF, REG) ... -
Page 5: Road Safety
Thank you for deciding in favour of a Blaupunkt product. We wish you a great deal of pleasure with your new car ra- dio. Before using your car radio, please read these instructions carefully. The Blau- punkt editors are constantly working to make our instruction manuals as clear and easy to understand as possible. -
Page 6: Flip/Release Panel
Your car radio is fitted with a flip/release panel to guard against theft. Without this panel, the unit is worthless to the thief. Protect your unit from theft by taking the flip/release panel with you every time you leave the car. Do not leave the panel behind in the car, even if it is out of sight. - Page 7 There are various ways of switching the car radio on and off, as described be- low. If the car radio is correctly connected to the ignition and has not been switched off using the button 3, it is switched on/off simultaneously with the ignition. You can also switch on your car radio when the vehicle ignition is off.
- Page 8 The system volume can be adjusted in steps from 0 (off) to 66 (maximum). To raise the system volume, turn the volume control 2 to the right. To lower the system volume, turn the volume control 2 to the left. You can set the volume at which you wish the car radio to play when switched Press the MENU button 8.
- Page 9 If you hold down a button for longer than two seconds when using certain func- tions, e.g. storing a station on a station button, a confirmation tone (beep) sounds. The volume of this beep is ad- justable. Press the MENU button 8. button : re- Press the peatedly until “BEEP”...
- Page 10 This unit is equipped with an RDS radio receiver. Many of the receivable FM sta- tions transmit a signal that not only car- ries the programme but also additional information such as the station name and programme type (PTY). The station name appears on the dis- play as soon as it is received.
- Page 11 In order to switch between memory levels or wavebands, briefly press the BND/TS button 5. There are various methods available for tuning into a station. button :. Press the The unit tunes into the next receivable station. You can also tune into stations manual- Press either the Note: You can only tune into stations...
- Page 12 You can store the six stations with the strongest reception in the region auto- matically (only FM). The stations are stored in the FMT memory. Note: Stations that were previously stored in this memory are deleted in the process. Hold down the BND / TS button 5 for more than two seconds.
- Page 13 When the programme type has been selected and the search started, the car radio switches from the current station to a station featuring the selected pro- gramme type. Note: If no station with the selected pro- gramme type is located, a beep sounds and “NO PTY”...
-
Page 14: Radio Mode
The HiCut function improves the sound during poor radio reception (only FM). If interference occurs, the treble is au- tomatically reduced and thus also the interference level. Press the MENU button 8. button : Press the repeatedly until “HICUT” appears on the display. - Page 15 Your car radio is equipped with an RDS- EON reception system. EON stands for Enhanced Other Network. When a traffic announcement (TA) is broadcast, your unit will automatically switch, within a broadcasting network, from a station which does not transmit traffic information to one that does.
- Page 16 You can use this unit to play standard CDs with a diameter of 12cm. Risk of damage to CD drive! Single CDs with a diameter of 8 cm and CDs which are not circular (“shape CDs”) should not be used. We accept no liability for any dam- age to the CD drive that may occur as a result of the use of unsuitable...
-
Page 17: Setting The Scanning Time
You can briefly listen in to all the tracks on a CD. Hold down the OK button ; for more than two seconds. The next track starts to play. Note: The scanning time is adjustable. Read about setting the scanning time in the section “Setting the scanning time”... -
Page 18: Fast Track Selection
Note: Information on handling CDs, in- serting CDs and operating the CD changer can be found in the oper- ating instructions accompanying your CD changer. Press the CD•C button @ repeat- edly until “CHANGER” appears on the display. Playback begins with the first CD the CD changer recognises. - Page 19 To play the tracks on the current CD in random order, press the but- ton 5 MIX >. “MIX CD” appears briefly on the display and MIX lights up. To play the tracks of all the inserted CDs in random order, press the button 5 MIX >...
- Page 20 / DIS 7 button briefly Press the to display the time. To set the time manually, press the MENU button 8. button : re- Press the peatedly until “CLOCKSET” ap- pears on the display. button :. Press the The time appears on the display. The minutes flash and can now be set.
-
Page 21: Tone And Volume Balance
You can adjust the tone and volume balance separately for every audio source (radio, CD, CD changer, AUX and traffic announcements). Note: Adjustments to tone and volume balance for traffic announcements can only be made during a traffic announcement. Press the AUD / LD = button. “BASS”... -
Page 22: Equalizer
Loudness means the bass and treble are increased to a comfortable level at lower volume levels. Press the AUD / LD = button for approx two seconds. When loudness is activated, LD lights up on the display. The loudness level can be raised in steps of one to six. - Page 23 In order to switch on the equalizer, hold down the EQ < button until DEQ lights up on the display and “EQ ON” appears briefly. To switch off the equalizer, hold down the EQ < button until DEQ goes out on the display and “EQ OFF”...
- Page 24 Commence settings at mid and treble section and complete them in the bass section. Sound impression/problem Bass reproduction too weak Muffled reproduction Low transparency No instrumental brilliance What to do Raise bass with frequency: 60 to 100 Hz (LOW EQ), level: +4 to +6 Raise tweeter range with frequency: approx.
-
Page 25: External Audio Sources
The AUX output has to be switched on in the install menu. To connect up an external audio source, you will need an adapter cable, obtain- able from any authorised Blaupunkt dealer. Press the MENU button 8. “MENU” appears on the display. -
Page 26: Guarantee
Not covered by such guar- antee are damage caused by wear and tear, improper use or commercial use. In order to claim the Blaupunkt manu- facturer's guarantee, please send in the defective unit along with proof of pur- chase to the central Blaupunkt after- sales department in your country.