Toshiba AW-7480EM Owner's Manual page 13

Attaching the water supply hose to the faucet
If you attach the water supply hose completely, it may cause a water leakage.
Faucet shape Wall-mounted faucets are best.
Wall-mounted Square
shaped faucet
The distance is needed
1.6 cm or more
Attaching the hose union
1 Push the lock lever of the water
supply hose. Pulling the sleeve down,
lower the entire hose to disconnect
the hose union.
2 Check the diameter of the faucet.
When the faucet mouth is large,
loose the screws and remove the
inside ring to facilitate, attachment.
3 Loose 4 screws of the hose union,
push the hose union to the water
faucet.
4 Tighten the four screws evenly
around the faucet. In this time check
the gap is approx. 4 mm between the
nozzle and the ring.
Connecting the water supply hose
1 Pull the sleeve down, then insert
the water supply hose.
2 Separate the sleeve until a click is
heard, then push it up.
3 Check to ensure that the lock
lever is hung on the nozzle. Next,
check to ensure that the water
supply hose does not come off by
pulling down on it.
The water inlet may be blocked by foreign
objects. Remove the water supply hose
and clean the filter with a brush.
•
If you remove the water supply care-
lessly, water may splash. Therefore, use
the following procedure.
Drain all water from the
basket, drainage hose
and water supply hose
after using the machine.
6348100701 (11-15)
INSTALLATION
Caution
•
•
Movable Multi-home
faucet faucet
•
•
Hose Union
Lock
lever
Sleeve
Water
supply
hose
Inside
ring
Ring
Approx.
4 mm
Joint
seal
4 Tighten the hose nut
Nozzle
Sleeve
Lock
lever
Water intake
valve
If the filling water becomes not good
Filter
Water
intake valve
In case of water may freeze
If the water is frozen
1 Remove the water supply hose and pour in warm water (under 40°C).
2 Fill warm water (under 40°C) into the basket until the pulsator is
completely covered. Leave it for 30 minutes. Then check to see whether
the pulsator can be turned by hand.
13
The old inlet hose should not be reused.
If the faucets are not suited, please contact your
dealer.
Do not connect the hot water supplying
convenience.
In order to provide a permanent source of
water for your washing machine, it is suggested
that a branching water pipe (available separately) be used.
5 Remove the seal from the union
and turn to the arrow destination
the nozzle to tighten securely.
6 Check the gap is approx. 1 to 3
mm between the nozzle and the
ring.
•
If the gap is wide, it may cause the water leak.
•
If it cause the water leakage during operation,
tighten the nozzle more securely.
Caution
•
If you attach the hose union again because of
moving house etc., loose the gap is approx. 4 mm
between the nozzle and the
ring. Then attach it according
above methods. They are
preventable the water leakage.
Caution
•
on the end of the
water supply hose
securely to the water
intake valve.
Water supply
Hose nut
hose
•
Removing the water supply hose
1 Turn the water faucet off.
2 Turn the power switch ON and press
the START/HOLD pad.
3 After indicating the water level,
loosen the hose nut of the machine
top and remove it.
22/10/08, 11:19
Branching
water pipe
Hose union
Ring
Approx.
1 to 3 mm
Nozzle
Approx.
4 mm
Check to ensure that the water
supply hose is properly installed by
turning the water on and checking for
leakage.
If there is leakage, connect it from the
first.
If you remove the water supply hose
after supplying water, water may
splash. Refer to the following
— "Removing the water supply hose".
under 40°C
13