Kohler K-163 Installation Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Installation Guide

Pedicure Spa

K-163, K-1006, K-1011,

K-1012

1063564-2-D

Table of Contents

Summary of Contents for Kohler K-163

Page 1 Installation Guide Pedicure Spa K-163, K-1006, K-1011, K-1012 1063564-2-D...
Page 2: Important Information
Do not relocate the footbath pump, or make other modiﬁcations to the footbath system, as this could adversely affect the performance and safe operation of the footbath. Kohler Co. shall not be liable under its warranty or otherwise for personal injury or damage caused by any such unauthorized modiﬁcation.
Page 3: Table Of Contents
Thank You For Choosing Kohler Company ........
Page 4: Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before you start installation. If you encounter any installation or performance problems, please don’t hesitate to contact us. Our phone numbers and website are listed on the back cover. Thanks again for choosing Kohler Company.
Page 5: Construct The Platform Framing
Lay the two footbath sled supports onto the stacked 2x4 supports but do not secure at this time. Optional: Construct steps, adjacent to the platform, opposite the faucet installation location. Two steps, are recommended, measuring 28-1/2″ (72.4 cm) wide with an 8″ (20.3 cm) rise and a 12″ (30.5 cm) run. Kohler Co. 1063564-2-D...
Page 6: Provide Electrical Service
If necessary, move the sled supports as needed to not interfere with the drain connections. Remove the footbath and return it to the carton. Install the rough water supply and drain piping. IMPORTANT! When required by local codes, install a RPZ backﬂow prevention device to each faucet supply line. 1063564-2-D Kohler Co.
Page 7: Install The Footbath
If necessary, move the sled supports as needed to not interfere with the drain connections. Secure the sled supports to the 2x4 supports and the footbath to the sled supports. Connect the drain to the trap according to the drain installation instructions. Kohler Co. 1063564-2-D...
Page 8: Complete The Platform Framing
Build a bump-out, using 1x4s, for the platform frame to accommodate the front footbath jet. This bump-out will allow the technician to sit closer to the footbath basin. Install the bump-out to complete the platform framing. 1063564-2-D Kohler Co.
Page 9: Prepare The Rough Deck Material
Mark the cutout for the footbath and access panel onto the deck material. Cut out the opening for the footbath and access panel in the deck material. Provide support around the edges of the access panel cutout to prevent the panel from falling through. Kohler Co. 1063564-2-D...
Page 10: Begin Tiling The Platform
Pre-cut or drill the tile as needed to align with the holes drilled in the rough deck. Install the tile to the platform. Do not cover the access on the faucet-side of the platform at this time. IMPORTANT! Allow the tile adhesive and grout to cure according to the manufacturers’ instructions before proceeding. 1063564-2-D Kohler Co.
Page 11: Install The Faucet And Air Switch
Slide the nut over the tube. Secure the air switch assembly to the platform with the nut. Attach the free end of the tube to the pump and secure with the nut until ﬁnger-tight. 9. Cut the Pump Banding Straps Cut the pump banding straps. Kohler Co. 1063564-2-D...
Page 12: Check Installation And Operation
Allow the footbath to run for approximately 5 minutes and check all piping connections for leaks. Rotate the jet trim rings to increase (counterclockwise) or decrease (clockwise) the ﬂow. Press the air switch again to turn off the footbath. 1063564-2-D Kohler Co.
Page 13: Complete The Platform
Tile Cover and complete Finish tile here. tile installation. 11. Complete the Platform Cover the platform opening and ﬁnish tiling the side of the platform. Kohler Co. 1063564-2-D...
Page 14: Install The Client Chair (If Used)
Remove plaster by carefully scraping with a wood edge. Do not use metal scrapers, wire brushes, or other metal tools. Use a powder-type detergent on a damp cloth to provide mild abrasive action to any residual plaster. Refer to the Maintenance Guide for additional cleaning information. 1063564-2-D Kohler Co.
Page 15: Troubleshooting Procedures
NOTE: When installed correctly, the jet should turn smoothly both clockwise and counterclockwise. Troubleshooting Guide This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or qualiﬁed electrician should correct any electrical problems. For warranty service, contact your dealer or wholesale distributor.
Page 16 Remove blockage and allow motor to cool. Check for jet blockage. Remove blockage and allow motor to cool. 4. Noisy operation. A. The pump banding straps have A. Using tin snips, cut the pump not been cut. banding straps. 1063564-2-D Kohler Co.
Page 17 1063564-2-...
Page 18 1063564-2-...
Page 19 1063564-2-...

This manual is also suitable for:

K-1006 K-1011 K-1012