Page 1 PORTÉGÉ M300 TOSHIBA PORTÉGÉ M300 Portable Personal Computer User’s Manual...
Page 2 This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA PORTÉGÉ M300 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice.
Page 3: Eu Declaration Of Conformity
Any consequences resulting from the use of this product in working environments that are not approved or the use is restricted are not the responsibility of TOSHIBA Corporation. The consequences of the use of this product in those working environments may be:...
Page 4 This product and the supplied accessories are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if accessories or cables not manufactured / distributed by TOSHIBA are connected or implemented. To avoid EMC problems in general, the following advice should be observed: Only CE marked accessories should be connected / implemented.
Page 5 Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121. Germany Greece Portugal Spain Switzerland All other countries/regions Specific switch settings or software setup are required for each network, please refer to the relevant sections of the user guide for more details.
Page 6: Optical Disc Drive Safety Instructions
User’s Manual Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic DVD-ROM&CD-R/RW UJDA765 The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Page 7 User’s Manual DVD Super Multi UJ-822 The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 8 User’s Manual International precautions CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TOEN60825 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTSLSE FOR STRÅLING viii CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.”...
Page 9 User’s Manual OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Page 10 User’s Manual User’s Manual...
Page 11: Table Of Contents
PORTÉGÉ M300 Table of Contents Preface General Precautions Introduction Chapter 1 : Equipment checklist ..........1-1 Hardware .
Page 12 RecordNow! Basic for TOSHIBA........
Page 13 Generating ASCII characters ......... . . 5-9 User’s Manual ® by TOSHIBA ......4-23 Table of Contents xiii...
Page 14 TOSHIBA Password Utility ........
Page 15 CF (CompactFlash) card..........8-5 Inserting a CF card .
Page 16 TOSHIBA support ........
Page 17 Table of Contents AC Power Cord and Connectors Appendix E : Certification agencies ..........E-1 If your computer is stolen Appendix F : Glossary...
Page 18 Table of Contents xviii User’s Manual...
Page 19: Preface
This manual tells how to set up and begin using your PORTÉGÉ M300 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Page 20 Preface Chapter 4, Operating devices: Touch Pad, USB floppy disk drive, optical media drives, sound system, modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs. Chapter 5, the keypad overlay and hot keys. Chapter 6, Power and Power-Up power resources and battery save modes and how to set a password.
Page 21: Key Operation
Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
Page 22 Preface xxii User’s Manual...
Page 23: General Precautions
PORTÉGÉ M300 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 24 General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phones Use of mobile phones can interfere with the audio system.
Page 25: Introduction
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 26: Software
TOSHIBA Zooming Utility TOSHIBA PC Diagnostic Tool TOSHIBA Controls Online manual Documentation PORTÉGÉ M300 Portable Personal Computer User’s Manual PORTÉGÉ M300 Quickstart Safety Instruction Manual Warranty information If any of the items are missing or damaged, contact your dealer immediately.
Page 27: Features
Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in Some models in this series carry Intel...
Page 28 Introduction Power Battery pack RTC battery AC adaptor Disks Hard disk drive (HDD) USB floppy disk drive (optional) Computers in this series are configured with one of the following optical media drives. The available optical media drives are described below. The computer is powered by one rechargeable lithium-ion battery pack.
Page 29 DVD-ROM&CD-R/RW drive DVD Super Multi drive User’s Manual Some models are equipped with a full-size, DVD-ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at maximum 24 speed and CD-RW at maximum 24 speed.
Page 30: Pointing Device
Introduction Display The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in Graphics controller Keyboard Built-in Pointing Device Built-in Touch Pad Ports External monitor Universal Serial Bus (USB 2.0)
Page 31 Infrared Slots PC card CF card SD card Multimedia Sound system Headphone jack Microphone jack User’s Manual The serial infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data transfer with IrDA 1.1 compatible external devices.
Page 32 Introduction Communications Modem Bluetooth An internal modem provides capability for data and fax communication. It supports V.90 (V.92). The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. Both of V.90 and V.92 are supported only in USA, Canada, UK, France, Germany and Australia.
Page 33 Wireless LAN The numerical values for display are the theoretical maximums for Wireless LAN standards. The actual values may differ. The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations.
Page 34: Special Features
Introduction Security Security lock slot Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Assist button TOSHIBA Presentation button Hot keys Display automatic power off...
Page 35 You can specify the setting in the When I close the lid item of the Setup Action tab in TOSHIBA Power Saver. When battery power is exhausted to the point that computer operation cannot be continued, the system automatically enters Hibernation and shuts down.
Page 36 Introduction Optical media drive power icon HDD Protection This function does not guarantee that the HDD will not be damaged. Hibernation Standby 1-12 Use this to turn the power of the optical media drive on or off. Clicking on the optical media drive icon on the taskbar will turn the power of the optical media drive on or off.
Page 37: Utilities
InterVideo WinDVD. This software enables communication between remote Bluetooth devices. The TOSHIBA SD memory boot utility is a utility which can create SD memory card to a boot disk. You can boot TOSHIBA SD Memory Boot Utility from the menu bar as follows. Click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD Memory Boot Utility.
Page 38 Introduction RecordNow! Basic for TOSHIBA TOSHIBA Assist TOSHIBA PC Diagnostic Tool TOSHIBA Mobile Extension TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to TOSHIBA TouchPad On/Off Utility TOSHIBA Password Utility TOSHIBA Accessibility DLA for TOSHIBA 1-14 You can create CD/DVDs in several formats...
Page 39: Options
A 256, 512 or 1,024 MB memory module (DDR 333) can easily be installed in the computer. An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. An additional battery pack can be purchased from your TOSHIBA dealer.
Page 40 Introduction Advanced Port Replicator III The PORTÉGÉ M300 does not support the DVI and i.LINK ports on the Advanced Port Replicator III. Wireless LAN Kit Bluetooth Kit Bluetooth SD card3 1-16 The Advanced Port Replicator III provides the ports available on the computer in addition to separate PS/2 mouse and PS/2 keyboard ports, a digital visual interface (DVI) port, i.LINK™...
Page 41: Chapter 2 : The Grand Tour
PORTÉGÉ M300 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your select model may not have...
Page 42: Left Side
The Grand Tour Display latch Microphone jack Headphone jack Volume control Wireless communication switch Set the switch to off in airplanes and hospitals. Check the wireless communication indicator. It will stop glowing when the wireless communication function is off. Left side The following figure shows the computer’s left side.
Page 43: Right Side
External monitor port PC card slot PC card eject button Keep foreign objects out of the PC card slot. A pin or similar object can damage the computer’s circuitry. Security lock slot Universal Serial Bus (USB 2.0) port Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry.
Page 44 The Grand Tour CF Card slot CF card eject button Keep foreign objects out of the CF Card slot. A pin or similar object can damage the computer’s circuitry. SD card slot Keep foreign objects out of the SD card slot. A pin or similar object can damage the computer’s circuitry.
Page 45: Backside
Backside The following figure shows the computer’s backside. DC IN 15V jack DC IN 15V jack LAN jack Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction. Do not connect the LAN cable to a power supply. It could cause damage or malfunction.
Page 46: Underside
The Grand Tour Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. Battery lock Memory module cover Battery lock Battery pack Notches Battery release latch Docking interface Keep foreign objects out of the docking interface port. A pin or similar object can damage the computer's circuitry.
Page 47: Front With The Display Open
Stereo speaker (Left) Power button LCD Sensor switch (Not shown) TOSHIBA Assist Button User’s Manual This cover protects one memory module socket one or no module is preinstalled. Refer to the Memory expansion Optional Devices .
Page 48 Hibernation mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is “enabled”. Refer to the TOSHIBA Power Saver and Panel Power Off/On items in Chapter 1, features, for details on settings.
Page 49 LCD and CRT. You can also return to single display by pressing this button twice. The setting of TOSHIBA Presentation button can be changed through the properties of TOSHIBA Controls. Display mode is changed to the multi-monitor display by selecting "Different Image"...
Page 50: System Indicators
The Grand Tour System indicators LEDs beneath icons, light when various computer operations are in progress. DC IN DC IN Power Battery Wireless communication SD card 2-10 Power Battery System indicators The DC IN indicator glows in green when DC power is supplied from the AC power adaptor.
Page 51: Keyboard Indicators
Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.
Page 52: Usb Floppy Disk Drive (Optional)
The Grand Tour USB floppy disk drive (optional) The optional USB floppy disk drive accommodates 1.44-megabyte or 720- kilobyte floppy disks. USB connector Disk-In-Use Indicator USB connector Disk-In-Use Indicator This indicator lights when the floppy disk is being Floppy disk slot Eject button Check the Disk-In-Use indicator when you use the USB floppy disk drive.
Page 53: Optical Media Drives
Optical media drives One of the following optical media drives is installed in the computer: DVD- ROM&CD-R/RW drive or DVD Super Multi drive. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the media drives Region codes for DVD drives and media...
Page 54: Dvds
The Grand Tour DVDs DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed. DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once. Formats The drives support the following formats: CD-ROM DVD-ROM CD-DA Photo CD...
Page 55: Ac Adaptor
Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of any other adaptors could damage your computer. TOSHIBA assumes no liability for any damage in such case. User’s Manual Power and Power-Up...
Page 56 The Grand Tour Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture. 2-16 User’s Manual...
Page 57: Getting Started
PORTÉGÉ M300 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Setting up your work space — for your health and safety Be sure also to read the Safety Instruction Manual. This guide, which is included with the computer, explains product liability.
Page 58: General Conditions
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. Make sure there is adequate space around the computer for proper ventilation. Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.
Page 59: Seating And Posture
Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips. Below eye level Foot rest Place your chair so that the keyboard is at or slightly below the level of your elbow.
Page 60: Work Habits
Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your workday. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency.
Page 61 Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of any other adaptors could damage your computer. TOSHIBA assumes no liability for any damage in such case. Do not use a 3-pin to 2-pin conversion plug.
Page 62: Opening The Display
Getting Started 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN 15V jack 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow.
Page 63: Turning On The Power
Turning on the power This section describes how to turn on the power. The Power button LED indicates the status. Refer to the section in Chapter 6, Power and Power-Up Modes . After you turn on the power for the first time, do not turn it off until you have set up the operating system.
Page 64: Turning Off The Power
Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen.
Page 65: Starting Hibernation
For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost.
Page 66: Standby Mode
When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. To restore operation from Standby mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.
Page 67: Restarting The Computer
1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.
Page 68: Restoring The Preinstalled Software
Getting Started Restoring the preinstalled software Some models in this series are prepared for Hard Disk Recovery. These models will come without a Product Recovery optical media and a Tools & Utilities CD-ROM. You can restore the preinstalled software depending on the model you purchased.
Page 69 2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu.
Page 70: Restoring From The Product Recovery Media
Restoring TOSHIBA utilities and drivers If Windows is working properly, individual drivers or applications can be separately restored. The Toshiba Tools & Utilities CD-ROM contains drivers and applications which were included with your computer system. If your system drivers or applications have become damaged in some way, this CD allows you to reinstall most of the components which are not part of the Windows operating system.
Page 71: Operating Basics
PORTÉGÉ M300 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the USB floppy disk drive (optional), optical media drives, Sound System, Modem, Wireless communication features and LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs.
Page 72: Using The Usb Floppy Disk Drive
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material.
Page 73: Disconnecting Usb Floppy Disk Drive
Disconnecting USB floppy disk drive When you have finished using the USB floppy disk drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all floppy disk activity has stopped. If you disconnect the USB floppy disk drive or turn off the power while the computer is accessing the drive you may lose data or damage the floppy disk or the drive.
Page 74: Loading Discs
Operating Basics Loading discs To load CD/DVDs, follow the steps below. 1. When the computer’s power is on, press the eject button to open the disc tray slightly. 2. Grasp the disc tray gently and pull until it is fully opened. 3.
Page 75: Removing Discs
When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat.
Page 76: How To Remove Cd/Dvd When The Disk Tray Will Not Open
Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can hold it. Hold the CD/DVD gently and lift it out. 3. Push the center of the disc tray to close it. Press gently until it locks into place.
Page 77: Writing Cds On Dvd-Rom&Cd-R/Rw Drive
Writing CDs on DVD-ROM&CD-R/RW drive The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the Using optical media drives CD-R discs can be written to only once.
Page 78: When Writing Or Rewriting
Operating Basics TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.
Page 79: Writing Cd/Dvds On Dvd Super Multi Drive
Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
Page 80 Operating Basics CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: (Multi-Speed and High-Speed) MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. CD-RW: (Ultra-Speed) MITSUBISHI CHEMICAL CORPORATION DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYO YUDEN CO., LTD.
Page 81 This drive cannot use discs that allow writing faster than 2 speed (DVD-R, DVD-RW, DVD-RAM), 2.4 speed (DVD+R, DVD+RW). If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it.
Page 82: When Writing Or Rewriting
Always copy data from the HDD to the DVD-RAM. Do not use cut-and-paste. The original data will be lost if there is a write error. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: DVD-Video cannot be created using RecordNow!.
Page 83: Data Verification
You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or DVD+R/+RW using the “Exact Copy” function of RecordNow!. You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or DVD+R/+RW to CD-R/RW using the “Exact Copy” function of RecordNow!. RecordNow! cannot record in packet format. You might not be able to use the “Exact Copy”...
Page 84: Dla For Toshiba
Operating Basics DLA for TOSHIBA Note the following limitations when you use DLA: This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that are not rewritable. DLA does not support formatting a DVD-RAM disc and writing to it.
Page 85: How To Make A Dvd-Video
How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click [Start]-[All Programs] - [InterVideo WinDVD Creator2] - [InterVideo WinDVD Creator] to launch WinDVD Creator. 2. Click [Capture] button then capture the video data from the DV-Camcorder via IEEE1394.
Page 86 Operating Basics While recording video to DVD or tape, please close all other programs. Do not run software like a screen saver because it can put a heavy load on the CPU. Do not run communication applications like a modem or a LAN. 2.
Page 87: Media Care
Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1.
Page 88: Sound System
Operating Basics Sound System This section describes audio controls including sound levels and power management. Volume Control The Volume Control utility lets you control the audio volume in Windows for both playback and recording. To launch Volume Control for playback, click start, point to All Programs, point to Accessories, point to Entertainment and click Volume Control.
Page 89: Modem
To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 90: Modem Selection
Operating Basics AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
Page 91: Disconnecting
2. Plug the other end of the modular cable into a telephone jack. Do not pull on the cable or move the computer while the cable is connected. If you use a storage device such as an optical drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: Modem speed is slow or communication is interrupted.
Page 92: Wireless Lan
TOSHIBA strongly recommend the customer to enable the WEP function. TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof. 4-22 or Super AG technology (Atheros module type).
Page 93: Bluetooth Wireless Technology
Detailed information regarding the use with these operating systems is listed below. Please refer also to the electronic information which is included with each software. This Bluetooth specification. TOSHIBA cannot confirm all compatibility among any PC products and/or other electronic devices using Bluetooth TOSHIBA mobile PCs. User’s Manual by TOSHIBA ®...
Page 94: Wireless Communication Switch
Release Notes related to the Bluetooth ® Windows 1. Install: On Windows2000 or Windows XP, Bluetooth TOSHIBA does not need signature. 2. Fax application software: Regarding FAX application software, there are some software that you cannot use on this Bluetooth 3. Multi User: On Windows XP, Multi user does not supported.
Page 95: Wireless Communication Indicator
Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indicator off Indicator glows If you used the Task Bar to disable W-LAN, restart the computer or follow the procedures below to enable the system to recognize W-LAN. Open or click the following: start, Control Panel, System, Hardware, Device Manager, Network adapters, Intel Network Connection or Atheros AR5004G/AR5004X Wireless Network...
Page 96: Connecting Lan Cable
Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.
Page 97: Cleaning The Computer
Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.
Page 98: Heat Dispersal
CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Performance...
Page 99: Chapter 5 : The Keyboard
PORTÉGÉ M300 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 100: Function Keys: F1
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 101: Hot Keys
Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay operate these keys.
Page 102 Fn, and release and press F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver.
Page 103 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.
Page 104: Fn Sticky Key
Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
Page 105: Windows Special Keys
Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.
Page 106: Temporarily Using Normal Keyboard (Overlay On)
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in the figure below. Press Fn + F11 again to turn off the overlay. Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay:...
Page 107: Temporarily Changing Modes
Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation.
Page 108 The Keyboard 5-10 User’s Manual...
Page 109: Chapter 6 : Power And Power-Up Modes
PORTÉGÉ M300 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Page 110: Power Indicators
Power and Power-Up Modes Battery charge adaptor is above low battery trigger connected point Battery charge is below low battery trigger point Battery charge is exhausted No battery installed Power indicators As shown in the above table, the Battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status.
Page 111: Dc In Indicator
DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Green Flashing orange No light Power indicator Check the Power indicator to determine the power status: Green Blinking orange No light Battery types The computer has three types of batteries: Battery pack High capacity battery pack (optional)
Page 112: High Capacity Battery Pack (Optional)
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost.
Page 113: Real Time Clock (Rtc) Battery
Troubleshooting The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
Page 114 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. 3. Make sure the battery is securely installed in the computer before attempting to charge the battery pack.
Page 115 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture.
Page 116: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
Page 117: Monitoring Battery Capacity
Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Page 118: Maximizing Battery Operating Time
How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: CPU Processing speed...
Page 119: Extending Battery Life
Extending battery life To maximize the life of your battery pack: At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below. 1.
Page 120: Replacing The Battery Pack
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced.
Page 121: Installing The Battery Pack
7. Return your computer to the upright position. For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery pack, follow the steps below.
Page 122: Toshiba Password Utility
( ). Battery lock 6. Return your computer to the upright position. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
Page 123 If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: start ->...
Page 124: Supervisor Password
This utility lets you do the following: Register, delete or change the supervisor password. Create or invalidate a supervisor password token. This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens. Specify restrictions for general users. Starting the computer by password If you registered a password, there are two ways to start the computer: Insert an SD card token before you turn on the computer.
Page 125: Power-Up Modes
Refer also to the sections in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation.
Page 126 Power and Power-Up Modes 6-18 User’s Manual...
Page 127: Chapter 7 : Hw Setup
PORTÉGÉ M300 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config, Parallel/Printer and USB. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
Page 128: Boot Priority
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Default About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you use the display to be used when the computer is booted.
Page 129 CD-ROM CD-ROM CD-ROM CD-ROM You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: FDD is looked for when the boot disk is contained in external FDD. When SD memory card is set as the boot disk, external FDD is looked for first.
Page 130 HW Setup 3. Use the left/right cursor keys to highlight the boot device you want and press Enter. If a supervisor password is set only, it is the following. The menu above appear when you use the user password to start the computer (able to run HW Setup).
Page 131 If you select Left Ctrl + Left Alt or Right Ctrl + Right Alt for this option, you cannot use the selected keys to reboot the computer in combination with the Del key. For example, if you select Left Ctrl + Left Alt, you must use Right Ctrl, Right Alt and Del to reboot the computer.
Page 132: Device Config
HW Setup Wake-up on LAN This feature lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enabled Disabled Do not install or remove an optional memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off.
Page 133 Parallel Port Mode The options in this tab are ECP and Standard Bi-directional. Standard Bi-directional USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled.
Page 134 HW Setup User’s Manual...
Page 135: Optional Devices
PORTÉGÉ M300 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory PC card SD card CF (CompactFlash) card Memory expansion...
Page 136: Pc Card
The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 137: Sd Card
SD memory cards are sold with format in conformity to the Standards of SD memory card. If you format the SD card again, be sure to format it with the utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format.
Page 138: Inserting An Sd Card
Optional Devices Inserting an SD card To insert an SD card, follow the steps below. 1. Insert an SD card in the SD card slot. 2. Press gently to ensure a firm connection. Make sure the SD card is oriented properly before you insert it. Removing an SD card To remove an SD card, follow the steps below.
Page 139: Sd Card Care
8. Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk In TOSHIBA SD Memory Boot Utility, a boot disk can be created with SD memory card. Refer to the CF (CompactFlash) card This slot accommodates CF card.
Page 140: Inserting A Cf Card
Optional Devices Inserting a CF card To insert a CF card, follow the steps below. 1. Press the CF card eject button to extend it. 2. Press the extended eject button to pop the Dummy card out slightly. 3. Insert the CF card into the slot. 4.
Page 141: Cf Card Care
When you remove a memory, please do not touch other portions of a computer. Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost.
Page 142: Installing Memory Module
Optional Devices Use a point size 0 Phillips screwdriver to remove and fasten the screws. Use of an incorrect screwdriver can damage the screw heads. Installing memory module Follow the steps below to install a memory module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off.
Page 143: Removing Memory Module
Be careful not to drop the screw inside the computer. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 7. Seat the memory module cover and secure it with one screw. 8.
Page 144: Battery Pack
Optional Devices 7. Grasp the module by the sides and pull it out. If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Do not touch the connectors on the memory module or on the computer.
Page 145: Usb Floppy Disk Drive
USB floppy disk drive The USB floppy disk drive module can be connected to the USB port. For details on connecting the USB floppy disk drive module, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer.
Page 146: I.link (Ieee1394)
There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
Page 147: Connecting
Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. Connecting the i.LINK(IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: You may need to install drivers for your i.LINK devices.
Page 148: Advanced Port Replicator Iil
Modem jack, LAN jack, External monitor port. The PORTÉGÉ M300 does not support the DVI and i.LINK ports on the Advanced Port Replicator III. The following ports and accessories are available on the Advanced Port Replicator III.
Page 149: Parallel Printer
6. Turn on the printer’s power. 7. Turn on the computer’s power. 8. Start the HW Setup program. Refer to Chapter 7, 9. Select the Parallel/Printer tab from the TOSHIBA HW Setup window. 10. Set the Parallel Port Mode and press OK.
Page 150: Security Lock
Optional Devices Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator III to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator III. The computer has a security lock slot on the left side and right side. Attach one end of a cable to a desk and the other end to the security lock slot.
Page 151: Troubleshooting
PORTÉGÉ M300 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 152: Preliminary Checklist
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. Make sure you turn on all peripheral devices before you turn on the computer.
Page 153: Hardware And System Checklist
Software Hardware Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals. Basic problems may occur in the following areas: System start-up Self test Power Password Keyboard Internal LCD display panel Hard disk drive DVD-ROM&CD-R/RW drive DVD Super Multi drive USB floppy disk drive...
Page 154: Power
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: The computer stops and does not proceed to display information or messages except the TOSHIBA logo.
Page 155: Ac Power
AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, for more information. Problem AC adaptor doesn’t power the computer (DC IN indicator does not glow green) Battery If you suspect a problem with the battery, check the DC IN indicator as well as the Battery indicator.
Page 156 If you frequently recharge a partially charged battery, the battery might not charge to its full potential. Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. User’s Manual...
Page 157: Password
5. Press Y key. BIOS setup will terminate and the computer will be rebooted. Procedure Refer to the TOSHIBA Password Utility Chapter 6, Power and Power-Up Modes . The Keyboard Procedure Check that the numeric keypad overlay is not selected.
Page 158: Internal Lcd Display Panel
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Problem No display Markings appear on the LCD screen. Problems above remain unresolved or other problems occur Hard disk drive Problem Computer does not boot from hard disk drive...
Page 159: Dvd-Rom&Cd-R/Rw Drive
DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Problem You cannot access a CD/DVD in the drive Some CD/DVDs run correctly, but others do User’s Manual Operating Procedure Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Check whether the drive power is on.
Page 160: Dvd Super Multi Drive
9-10 Procedure If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA. Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording.
Page 161: Usb Floppy Disk Drive
USB floppy disk drive For more information, refer to Chapter 4, Problem Drive does not operate There may be a faulty cable connection. Check Some programs run correctly but others do You cannot access the external 3 1/2" floppy disk drive SD card Refer also to Chapter 8, Problem...
Page 162: Pc Card
Troubleshooting PC card Refer also to Chapter 8, Problem PC card error occurs CF card Refer also to Chapter 8, Problem CF card error occurs You cannot read a file Infrared port Refer also to the documentation for your IrDA compatible device and related software.
Page 163: Pointing Device
Pointing Device If you are using a USB mouse, also refer to the and to your mouse documentation. Touch Pad Problem On-screen pointer does not respond to Pad operation Double-tapping does not work The mouse pointer moves too fast or too slow When the reaction of Touch pad is sensitive...
Page 164 Troubleshooting USB mouse (optional) Problem On-screen pointer does not respond to mouse operation Double-clicking does not work The mouse pointer moves too fast or too slow The mouse pointer moves erratically 9-14 Procedure The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it.
Page 165: Usb
Refer also to your USB device’s documentation. Problem USB device does not work Memory expansion Refer also to Chapter 8, memory modules. Problem Beep sounds. (Two beeps, a dash and a dot, for a defective memory module in slot.) User’s Manual Procedure Check for a firm cable connection between the USB ports on the computer and the USB device.
Page 166: Sound System
Troubleshooting Sound System Refer also to documentation for your audio devices. Problem No sound is heard External monitor Refer also to Chapter 8, documentation. Problem Monitor does not turn No display Display error occurs 9-16 Procedure Adjust the volume control dial. Check the software volume settings.
Page 167: I.link (Ieee1394)
i.LINK (IEEE1394) Problem i.LINK device does not function Modem Problem Communication software can’t initialize modem You can hear a dial tone but can’t make a call You place a call, but a connection can’t be made After making a call you can’t hear a ring Communication is cut off unexpectedly...
Page 168: Lan
Troubleshooting Problem You cannot receive an incoming call Problem Cannot access LAN Wake-up on LAN does not work Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Problem...
Page 169: Bluetooth
Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Cannot access Bluetooth device Printer Refer also to the and to the troubleshooting and other relevant sections in your printer and software documentation. Problem Printer does not turn on. Check that the printer is connected to an electric Computer/printer do not communicate Printer error...
Page 170: Toshiba Support
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 171: Specifications
PORTÉGÉ M300 Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size Environmental Requirements Conditions Operating Non-operating Thermal Gradient Wet-bulb temperature Conditions Operating Non-operating Power Requirements AC adaptor Computer User’s Manual Appendix A 286.0 (w) × 233.0 (d) × 28.9/32.9(h) millimeters (not...
Page 172: Built-In Modem
Specifications Built-in Modem Network control unit (NCU) Type of NCU Type of line Type of dialing Control command Monitor function Communication specifications Communication system Communication protocol Communication speed Transmitting level Receiving level Input/output impedance Error correcting Data compression Power supply Telephone line (analog only) Pulse Tone...
Page 173: Display Controller And Modes
PORTÉGÉ M300 Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) support for the internal LCD and external monitors.
Page 174 Display Controller and Modes Video Type Resolution Character mode 0, 1 40 × 25 Text Characters 2, 3 80 × 25 Text Characters 0*, 1* 40 × 25 Text Characters 2*, 3* 80 × 25 Text Characters 0+, 1+ 40 × 25 Text Characters 2+, 3+...
Page 175 Table1 Video modes (VGA) continued Video Type Resolution Character mode 320 × 200 Grph Pels 640 × 200 Grph Pels 640 × 350 Grph Pels 640 × 350 Grph Pels 640 × 480 Grph Pels 640 × 480 Grph Pels 320 ×...
Page 176 Display Controller and Modes Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 1400 × 1050 1600 × 1200 1920 × 1440 2048 × 1536 Some video modes are not supported in the following modes: the Internal/ External Simultaneous Display mode and the Internal/External Multi Monitor mode.
Page 177 Table 2 Video modes continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 1400 × 1050 1600 × 1200 1920 × 1440 2048 × 1536 Some video modes are not supported in the following modes: the Internal/ External Simultaneous Display mode and the Internal/External Multi Monitor mode.
Page 178 Display Controller and Modes Table 2 Video modes continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 1400 × 1050 1600 × 1200 Some video modes are not supported in the following modes: the Internal/ External Simultaneous Display mode and the Internal/External Multi Monitor mode.
Page 179: Display Settings
Display settings 1. You cannot move from the [Settings] tab of [Display Properties] to the multi-monitor when you are using the display of the computer and an external CRT display or a TV at the same time. *The [Settings] tab is displayed in the following steps; 1) Open [Control Panel], click [Appearance and Themes].
Page 180 Display Controller and Modes 3) Select either Monitor (CRT display) or Television, then select Apply button, because the Primary Device is fixed into Notebook (the display of the computer). Intel(R) 82852/82855 GM/GME Graphics Controller Prope...(1) 2. Some reproduced DVD picture may not be displayed when the display of the computer and a CRT display are used at the same.
Page 181: Wireless Lan
PORTÉGÉ M300 Wireless LAN Card Specifications Form Factor Compatibility Network Operating System Media Access Protocol Data Rate User’s Manual Appendix C Mini PCI Type III IEEE 802.11 Standard for Wireless LANS Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
Page 182: Radio Characteristics
Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Page 183: Wireless Ieee 802.11 Channels Sets (Revision B And G
Frequency Range Channel ID *1 Factory-set default channels *2 Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the countries/regions in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed...
Page 184: Wireless Ieee 802.11 Channels Sets (Revision A
Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision A) Frequency Range Channel ID 5150-5850 MHz 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 User’s Manual...
Page 185: Wireless Channels Sets (Turbo Mode
Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID *3 These channels are available to Atheros module type only. Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID *4 These channels are available to Atheros A/B/G combo type only. User’s Manual 2400-2483.5 MHz 2437 5150-5850 MHz...
Page 186 User’s Manual...
Page 187: Bluetooth Wireless Technology Interoperability
Bluetooth wireless technology Interoperability Bluetooth Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: Bluetooth Specification Ver.1.2, as defined and approved by The Bluetooth Special Interest Group.
Page 188 Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/ computers/tnt/bluetooth.htm in Europe or http://...
Page 189: Bluetooth Wireless Technology And Your Health
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 190: Caution: Fcc Interference Statement
In order to comply with FCC radio frequency radiation exposure guidelines for an uncontrolled environment, the Bluetooth TOSHIBA has to be operated while maintaining a minimum body to antenna which are located on top of LCD distance of 20 cm. Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.
Page 191: Taiwan
Relevant transmitters include FCC IDs: CJ6UPA3375WL, CJ6UPA3232BT Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment. Taiwan Article 14 Unless approved, for any model accredited low power radio...
Page 192: Using Bluetooth
2. In case that RF interference occurs to Other Radio Stations from this equipment, please change promptly the frequency for use, place to use, or stop emitting Radio. 3. Please contact TOSHIBA Direct PC if you have a problem, such as interference from this equipment to Other Radio Stations.
Page 193: Device Authorization
3. TOSHIBA Direct PC Monday - Friday: 10:00-17:00 Toll Free Tel Direct Dial Device Authorization This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business of Japan.
Page 194 Do not use this equipment except in the countries/regions in the following table. Australia Canada Germany Japan New Zealand Switzerland Greece Portugal Countries/regions that have approved Bluetooth Card from TOSHIBA equipment is approved to the radio Austria Denmark Iceland Luxembourg Norway Italy Spain Belgium Finland Ireland...
Page 195: Certification Agencies
PORTÉGÉ M300 AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following...
Page 196 In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S.
Page 197 What is your address, phone, and fax number? To register the theft on paper, please follow these procedures: Fill in the TOSHIBA Theft Registration form (or a copy of it) below. Attach a copy of your receipt showing where your computer was purchased.
Page 198 If your computer is stolen TOSHIBA Theft Registration Send to: Fax number: Country stolen: Machine type: (e.g. TOSHIBA Pocket PC e350) Model number: (e.g. PSA50 YXT) Serial number: (e.g. 12345678G) Date stolen: Owner’s details Last name, first name: Company: Street:...
Page 199 PORTÉGÉ M300 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange...
Page 200 Glossary IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory...
Page 201 analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
Page 202 Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate.
Page 203 compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Page 204 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
Page 205 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
Page 206 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 207 jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
Page 208 Glossary mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.
Page 209 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
Page 210 Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device.
Page 211 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Page 212 Glossary Glossary-14 User’s Manual...
Page 213 User’s Manual CF card 7 Cleaning the computer 27 Cooling vents 2 DC IN indicator 10 Display 6 DLA for TOSHIBA 14 Docking interface 6 Documentation list 2 DVD Super Multi drive 5 care 7 inserting 6 location of slot 3...
Page 214 Index DVD-ROM&CD-R/RW drive 5 location of slot 3 problems 9 using 3 writing 7 Environment 1 Equipment checklist 1 Equipment setup general conditions 2 placement 2 Ergonomics lighting 3 seating and posture 3 work habits 4 Floppy disk care 17 Fn + Ctrl (enhanced keyboard simulation) 3 Fn + Enter 3...
Page 215 Index Keyboard 6 emulating enhanced key- Fn Sticky key 6 Function keys F1...F12 2 hot keys 3 problems 7 typewriter keys 1 Windows special keys 7 Keypad overlay 10 Arrow mode 7 Numeric mode 8 temporarily using normal temporarily using overlay turning on the overlays 7 LAN 8 cable types 25...
Page 216 Security lock 15 Soft keys checklist 3 Sound System 18 Standby 12 Self test 3 Sound System 16 support from TOSHIBA 20 System start-up 3 Touch Pad 13 USB 15 USB floppy disk drive 11 Wireless LAN 18 care 5...
Page 217 TOSHIBA ConfigFree 14 TOSHIBA Controls 13 TOSHIBA Mobile Extension 14 TOSHIBA PC Diagnostic Tool TOSHIBA Power Saver 13 TOSHIBA Presentation button TOSHIBA SD Memory Boot Util- ity 13 TOSHIBA Theft Registration 2 TOSHIBA Zooming Utility 13 USB 6 location 2...
Page 218 Index Index-6 User’s Manual...

Toshiba PORTEGE M300 User Manual

Chapter 1 Introduction

Chapter 2 : the Grand Tour

Chapter 3 Getting Started

Chapter 4 Operating Basics

Chapter 5 : the Keyboard

Chapter 6 : Power and Power-Up Modes

Chapter 7 : HW Setup

Chapter 8 Optional Devices

Chapter 9 Troubleshooting

Appendix A : Specifications

Appendix B : Display Controller and Modes

Appendix C : Wireless LAN

Appendix D : Bluetooth Wireless Technology Interoperability

Quick Links

Related Manuals for Toshiba PORTEGE M300

Summary of Contents for Toshiba PORTEGE M300