Advertisement
Quick Links
BEFORE YOU BEGIN
BEFORE YOU BEGIN
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
·
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
·
These instructions contain important care, cleaning,
and warranty information-
instructions for the consumer.
·
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
·
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 2 for reference.
·
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
CAUTION: Risk of injury or product damage.
Tempered glass cannot be cut, drilled or knocked
by hard object. Make sure corner area of the
glass refraining from knocking so as to cause
personal injury due to broken glass.
ATTENTION:
Please install this door on Kohler
receptors or curbs. (Not included). If the curb is not
Kohler-branded, please note its top width should be
more than 80mm.
IMPORTANT:
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
1197575-T01-B
please leave these
·
·
·
·
·
·
:
).
13-1
-1-
MINIMA
INSTALLATION INSTRUCTIONS
SLIDING, L SHAPE
8mm K-45805T
10mm K-45808T
2
(
80mm
3mm/m
528437
Copyright Kohler China Ltd., 2014
L
, 2014
Advertisement
Related Manuals for Kohler MINIMA K-45805T
Summary of Contents for Kohler MINIMA K-45805T
- Page 1 · · All information is based on the latest product information available at the time of publication. Kohler China Ltd. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. · ·...
-
Page 2: Parts Identification
ROUGHING-IN Unit: mm K-45805T 1200-1600 700-1100 1850-2000 K-45808T PARTS IDENTIFICATION PARTS IDENTIFICATION IMPORTANT Before installation check that all components are correctly supplied. If any parts are missing please ring the helpline. 800-820-2628 800-820-2628 Door Panel Top Lintel Side Panel Inline Panel Wall Channel Glass Clamp Splashguard... - Page 3 Mid-support Clamp Top Roller Clamps 4mm Allen key 3mm Allen Key Top Cap End Socket End-support Clamp Bottom Guide Plastic Guides Door Closing Guide Support Strip Frame Cap,LH Frame Cap,RH Wall Plugs Screw Covers Wedge Screw Covers Handle 1197575-T01-B...
-
Page 4: Installation Requirements
INSTALLATION REQUIREMENTS INSTALLATION REQUIREMENTS Tools Required · · Phillips Screwdriver · · Pencil · · Caulk Gun · · Measuring Tape · · Safety Glasses · · Center Punch · · Hammer · · Knife · · Masonry Drill & 6mm Drilll Bit ·... - Page 5 Fit wall channels x2 NOTE: Glass seal will extend out of wall channel. Wall channels MUST plumb. STEP 53mm Ensure the support strips are still on the bottom edge of the side panel, inside the H section, and that the H section is 53mm from the corner of the glass.
- Page 6 Glass needs to be at least 8mm into wall channel. 8mm minimum Caution Rest panel against seal of wall channel. Support panel until glass clamp is fitted. Bottom channel fits under seal. Panel needs to be parallel to edge of tray. STEP Fit glass clamp and turn screw until it lightly grips glass.
- Page 7 When glass is in correct position, fully tighten glass clamp screws, retighten screws after 10 minutes. Glass panel MUST plumb. 15mm Make sure that distance between edge of glass and wall channel "A" outer corner projection is 15mm. 15mm STEP Ensure the support strips are still on the bottom edge of the inline panel, inside the H section, and...
- Page 8 Rest panel against seal 8mm minimum of wall channel "A". Glass needs to be at least Caution 8mm into wall channel. Support panel until glass clamp is fitted. Bottom channel fits under seal. Panel must be parallel to edge of tray. STEP Fit glass clamp and turn screw until it lightly grips When glass is in correct position fully tighten glass...
- Page 9 Top view Mark hole position remove temporarily the bottom guide and drill hole into the tray. STEP STEP Lay a bead of sealant in bottom guide as shown, then slide it under glass. Keep threshold position parallel to tray edge. STEP Locate one end of threshold under the bottom guide.
- Page 10 Lift side panel and fit end cap guide.Lift Side Panel and Fit End Cap Guide and Threshold Cover. Caution STEP Cut seals exposed at top with Fit top cap. a sharp knife. Screw bottom guide to tray. Top view Fit screw covers.
- Page 11 Position support clamps and sockets on top lintel. Fully tighten mid support clamp "2" & loosely fit end sockets "1" & "3". Turn with allen key to lightly grip the top lintel. Screw mid support clamp to lintel. STEP Slide lintel and sockets to position on top of glass and wall channels. STEP 1197575-T01-B -11-...
- Page 12 Fix end support clamp firmly to glass. Screw mid support clamp firmly to glass. STEP STEP Screw socket to wall channel then tighten the allen screws on both sides. Carefully turn door panel on its edge Fit splashguard to and support. bottom of door 10mm from the closing edge.
- Page 13 Place support strip. Place support spacer. Caution Fit door. Lower panel onto supports. STEP Fit rollers clamps to top lintel and door panel. Lift door panel slightly Ensure screws are securely tightened. and remove support strip. Front Slide door open and remove support spacer.
- Page 14 Fit seals on: Notched seal Closing edge Back edge Door panel Door panel Inline panel STEP Fit plastic guides into bottom guide. Carefully apply silicone sealant along the back face to fix the plastic guide in place. STEP 1197575-T01-B -14-...
- Page 15 Fix handle. Fix cap. STEP STEP Lay a thin bead of sealant. Allow at least 24 hours before using shower to allow sealant to cure. 24hrs STEP STEP 1197575-T01-B -15-...