Related Manuals for Hunter Pendleton Series
Summary of Contents for Hunter Pendleton Series
- Page 1 Collection Installation Manual Model: 59389 Spider Rock / Eagle Rock Matte Black 59390 Canyonlands / Pecos Matte Silver Fan weight ±2 lbs: 24.7 lbs (11.2 kg) ©2018 Hunter Fan Co. PG3705 r101618...
- Page 2 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. c.2 - Use only Hunter replacement parts. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 3 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have Hunter Pro Tip: grouped the drawn components below with the hardware you’ll need for those Do not discard the hardware bags or mix parts from parts.
-
Page 4: Choosing The Right Installation Location
A little more information on Angled Mounting: For optimum performance and appearance, a longer downrod should be used with your Hunter ceiling fan when installing on high or angled ceiling. If your ceiling is angled greater than 34° you will also need an Angled Mounting Kit. -
Page 5: Installing The Ceiling Bracket
You have two options for installation. Pick which one works best for your location. Remove any existing Hunter Pro Tip: bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. The machine screws are the ones that came with your outlet box. -
Page 6: Hanging The Fan
1886 Hanging the Fan NOTICE To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod. Place the downrod ball into the slot in the ceiling bracket. Ceiling Bracket Hanging Fan Wiring Canopy Blades Light Glass Remote Troubleshooting Downrod... -
Page 7: Wiring The Fan
If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: Here is how to connect the wires: 4 Wire Nuts (these are in the... -
Page 8: Installing The Canopy
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. Canopy Screw Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Blade Screw Attach each blade to a blade iron using three blade washers, found in the hardware bag, and three blade assembly screws, found in the... -
Page 9: Assembling The Light Kit
1886 Assembling the Light Kit 2 of 7 2 of 7 Light Kit Screw Light Kit Screw Align the screw holes in the LED assembly with the screw holes in the trim ring. Screw two LED assembly screws, found in the hardware bag Partially install two light kit screws, found in the hardware through the LED assembly and into the trim ring. -
Page 10: Installing The Glass
1886 Installing the Glass Notch WARNING Position the notches in the outer rim of the globe so they line up with the three tabs on the inside rim of the housing. Carefully lift the globe up inside the GLASS FALL HAZARD NOTE: Check to ensure housing as far as it will go, then rotate the globe To prevent SERIOUS INJURY or DEATH, make... -
Page 11: Preparing The Remote
1886 Preparing the Remote To access the battery compartment, remove the small Phillips head screw that Battery secures the battery door to Door the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. -
Page 12: Troubleshooting
Hunter instructions, accidental damage caused by the fan owner or related parties, Please do not ship your fan or any fan parts to Hunter. Delivery will be refused. modifications to the fan, improper or incorrectly performed maintenance or repair,... - Page 13 1886 Downrod If you need a different downrod length follow these steps: Follow steps 1-5 to remove standard downrod pipe Follow steps 6-10 to reassemble with new downrod WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS tighten setscrew with pliers. •...