Summary of Contents for Vector LED-P
- Page 1 User Manual Vector LED Curing Light ® Vector LED-P Instructions For Use VECTOR R & D INC. 6824 19TH ST#230 UNIVERSITY PLACE WA 98466 USA; Website: www.vectorusa.net S-19-01-1125-UV101 V1.3...
-
Page 2: Table Of Contents
Table of Content No. Content Page Precautions And Safety Notes p. 3 Glossary of Symbols p. 4 Product Description & Fields of Application p. 5 Package Content p. 5 Technical Data p. 6 Charging base Hand piece Charging base and Handpiece Transportation and Storage Environment Installation of the unit p. -
Page 3: Precautions And Safety Notes
1. PRECAUTIONS AND SAFETY NOTES PLEASE NOTE! Prior to installation and start-up of the unit, carefully read the instructions provided herein! As with all technical devices, the proper function and safe operation of this unit depend on the user’s compliance with the safety recommendations presented in these operating instructions. CAUTION: This curing unit produces high curing energy output! A significant increase in curing energy is possible compared with conventional Halogen equipment you have previously used. -
Page 4: Glossary Of Symbols
Curing LED, open or alter the unit in any way 7. Use only genuine Vector R & D parts when replacing defective components as directed in these Operating Instructions. The product’s warranty does not cover any damage resulting from the use of third-party replacement parts. -
Page 5: Product Description & Fields Of Application
The Vector LED-P LED curing light is a fast-curing LED curing light. It emits typical light output at about 1,400 mW/cm². 3 Seconds to cure most resin-based composite in the market. It also features: Digital timer display, multiple mode selection: boost (fast curing) and ramp up (soft start), ►... -
Page 6: Technical Data
5. TECHNICAL DATA 5.1 Charging Base Operating voltage: INPUT: 100~240VAC, 2 A , 50/60HZ OUTPUT: 5 V DC , 2 A Dimensions Diameter: 90 mm Height: 75 mm Weight: Roughly 150 g 5.2 Handpiece Power supply: Lithium battery – 4.2V DC, 2100mAh Wavelength range: 440-480 nm Typical light intensity... -
Page 7: Installation Of The Unit
NOTE: Upon receiving the LED Curing Light, check the packaging and parts for any possible damage that may have occurred in transit. If damage is apparent, please contact your authorized Vector R & D distributor from which the light was purchased. -
Page 8: Keypad And Modes
5. Plug the connector of the power supply into the back of the charging base, or plug it into the bottom end of the Light itself, as shown in Figure 4. Plug the other end of the power supply into the appropriate electrical outlet. -
Page 9: Timer Selection
Power Indicator Illuminates when handpiece is connected Timer Display to power supply. High Intensity mode indicator Charging indicator Illuminates during Ramp mode charging, turn off indicator after fully charged. Figure 6 Figure 7 6.3 Timer selection: (H) Boost – This mode provides high power to the LEDs, helping them generate a higher power output up to 1,400 mW/cm2. -
Page 10: Operation Instruction
7. OPERATION INSTRUCTION Activating and Deactivating the Light: The light will enter “sleep” mode if the unit has not been used for more than 1 minute, the panel ► display will turn off to conserve power. If the panel display is not illuminated, simply press on/off button to bring it out of the sleep mode. -
Page 11: Operating Errors / Trouble Shooting
8. OPERATING ERRORS AND TROULE SHOOTING Problem Cause Solution ► No timer display on handpiece. The unit is in sleep mode. Press the on/off button to wake the unit. ► Can not activate/wake the light. Battery is drained. Please recharge battery, and try again. ►... -
Page 12: Service And Replacement Parts
9. SERVICE AND REPLACEMENT PARTS For product service please contact your nearest Vector R & D authorized dealer you purchased product. Replacement Accessories Part # Description Contents 1125B70 Vector LED-P Wall Plug-In Power Supply 1x Power Supply 1125B80 Vector LED-P eye protection shield... -
Page 13: Cleaning / Disinfecting / Sterilizing
10. Cleaning / Disinfecting / Sterilizing 10.1 Cleaning and Disinfection of Fiber Optic Light Guide Clean and disinfect the light guide before every use. The light guide is not sterile when delivered and ► must be sterilized before being used for the first time. Please check the manufacturer’s information about the cleaning and disinfecting agents. -
Page 14: Clean Charging Base, Handpiece, And Glare Shield
Dispose of battery and units in accordance with local legal regulations. 12. Disclaimer VECTOR R & D considers itself responsible for the effects on safety, reliability and performance of this product only if: Assembly operations, extensions, re-adjustments, modifications or repairs are carried out by ►... -
Page 15: Warranty
13. Warranty 13.1 Malfunction Vector R & D hereby warrants that for a period of one year from the delivery date, this device shall be free from defects in material and workmanship. In case the machine is found malfunctioned under normal use, Vector R &...