Philips AJ300D/12 User Manual page 5

5. Repeat the steps 3 - 4 until you complete all the other settings for minutes,
year, month and days.
TUNER
1 Press TUNER/AUX once to switch on the radio (FM only).
™ Display shows the radio frequency of the last selected waveband. Your
preset station is also shown if you are listening to a preset. (See 2)
2 Adjust the sound using VOL+/-.
3 To select preset stations, press the respective PRESET button (1-5).
TUNING TO RADIO STATIONS
1 Press and hold ¡1 / 2™ until the frequency in the display starts changing.
™Display shows "Scrh" during automatic tuning.
™After the system tunes to a station of sufficient reception, display shows its frequency.
• To tune to a weak station, press ¡1 / 2 ™ briefly and repeatedly until an
optimal reception is found.
To improve reception (FM):
Extend and position the pigtail fully to obtain optimum reception.
STORING AND USING PRESET STATIONS
You can store up to 5 FM radio stations in the memory.
1 Tune to your desired station (see TUNING TO RADIO STATIONS).
2 To store a preset, hold down briefly on a PRESET button 1-5 until you hear a dou-
ble beep.
™ Display shows the preset number of your station.
3 Repeat steps 1 and 2 to store your other stations.
• You can overwrite a preset station by storing another frequency in its place.
4 Press a PRESET button 1-5 (or PRESET 4 / 3 on the remote control) to listen to
a preset station.
™ To display clock time, press 2; on the set.
USING THE ALARM
GENERAL
Two different alarm times can be set. This can be useful when you need to be
woken up at a different time e.g. during the week and at the weekend, and you
can set different wake-up modes:
• tuner mode.
• buzzer mode. The gentle wake buzzer alarm increases its beep tone frequency within seconds.
• dock mode (only for Apple iPod and Philips GoGear SA9100 and SA9200)
SETTING THE ALARM TIME (See 3)
1 In any mode, press and hold ALM1 or ALM2 for two seconds.
™ ALM1 / ALM2 icon and the hour digits flash. And the icon for the current
alarm mode also flashes.
2 Hold down or press ¡1 / 2™ repeatedly to set and adjust the hours.
3 Press ALM1 or ALM2 to confirm.
™ ALM1 / ALM2 icon and the minutes digits flash. And the icon for the cur-
rent alarm mode also flashes.
4 Hold down or press ¡1 / 2™ repeatedly to set and adjust the mintues.
5 Press ALM1 or ALM2 to confirm.
SETTING THE ALARM MODE
1 Press POWER to switch to standby mode.
2 Select your choice of alarm mode: either docked player (only for Apple iPod
and Philips GoGear SA9100 and SA9200), buzzer, or radio by using the
• •
DOCK BUZZER TUNER slider.
• At the set alarm time, the docked player (only for Apple iPod and Philips GoGear
SA9100 and SA9200) or radio or buzzer will switch on automatically.
Helpful hints:
– If you have selected TUNER alarm mode, make sure you have properly tuned to a
station before turning off the set.
– If you have selected DOCK alarm mode (only for Apple iPod and Philips GoGear
SA9100 and SA9200), make sure you have docked the compatible player, or the
buzzer mode will be selected automatically.
– To check the alarm time setting for ALM1 or ALM2, press ALM1 or ALM2.
SWITCHING OFF THE ALARM
There are three ways of switching off the alarm. Unless you cancel the alarm
completely, the 24-hour ALARM RESET will be automatically selected after 59
minutes from the time your alarm first goes off.