1. Manuals
  2. Brands
  3. Harbor Freight Tools Manuals
  4. Nail Gun
  5. Central Pneumatic Professional 90437
  6. Assembly and operating instructions manual

Harbor Freight Tools Central Pneumatic Professional 90437 Assembly And Operating Instructions Manual

2” to 3-9/16” size coiled fasteners
Hide thumbs
Table of Contents

Advertisement

Quick Links

®
NAILER
2" TO 3-9/16" SIZE COILED FASTENERS
Model 90437
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http//www.harborfreight.com
Copyright 2003 by Harbor Freight Tools
®
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.

Advertisement

Table of Contents
loading

Related Manuals for Harbor Freight Tools Central Pneumatic Professional 90437

Summary of Contents for Harbor Freight Tools Central Pneumatic Professional 90437

  • Page 1 Copyright 2003 by Harbor Freight Tools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353.

  • Page 2: Product Specifications

    PRODUCT SPECIFICATIONS e l i n i f s l i " 3 " 1 " 2 " 6 e l i n i f s l i y t i l i o n i t o i t t e l "...
  • Page 3 REPLACEMENT PARTS AND ACCESSORIES: When servicing, use only identi- cal replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. MAINTAIN THIS PRODUCT WITH CARE. Keep this product clean and dry for better and safer performance.

  • Page 4: Specific Product Warnings And Precautions

    Maintain labels and nameplates on the Nailer. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replace- ment. Use only clean, dry, regulated, compressed air at between 65 to 100 PSI.
  • Page 5 Connect the air supply hose to the Nailer before loading the nails to pre- vent a nail from being accidentally fired during connection. The Nailer’s driving mechanism may cycle when the tool is connected to the air supply hose. When not in use, remove all nails from the Lower Nail Housing (part #75) of the Nailer.
  • Page 6 When unpacking, check to make sure all the parts shown on the Parts List (page 10) are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
  • Page 7 To Prepare The Nailer Before Driving: CAUTION! Keep the Nailer pointed away from yourself and others at all times. Always connect the Nailer to its air supply hose before loading nails. (See Figure D.) Do not load nails with Trigger (part #54) or Safety Guide (part #41) de- pressed.

  • Page 8: Inspection, Maintenance, And Cleaning

    be directed away from the operator. (See Figure D.) To Operate The Nailer: There are two ways to drive nails with the Nailer: The first way is to place the nose of the Nailer on the workpiece surface. Lightly push the tool toward the workpiece surface until the Safety Guide (part #41) is depressed.

  • Page 9: Please Read The Following Carefully

    drops of air tool oil into the air inlet of the tool at the beginning of each work day. To clean, blow the Nailer with compressed air. Then, use a non-flammable cleaning solution to wipe the exterior of the tool. Do not soak the tool with clean- ing solutions.

  • Page 10: Parts List

    PARTS LIST SKU 90437 PAGE 10...

  • Page 11: Assembly Diagram

    ASSEMBLY DIAGRAM NOTE: Parts #92 through #97 not shown. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 90437 PAGE 11...

Table of Contents