Hyundai J9F57 AC200 Manual

Copy OEM Logo Here (→)
Electronic Installation Instructions
If this is a printed copy of the installation instructions, ensure you have the latest revision by
scanning the QR code or by entering the website address listed below before beginning
Entered by
installation. Use the latest revision date as noted by "Rev. Date" above.
MPA
www.hyundaiaccessories.com/admin_media_uploads/installationSheets/j9f57_ac200.pdf
Application Notes
Vehicle should be equipped with automatic transmission, power door locks, and power windows. If these features are not equipped on the vehicle, do not proceed with install.
Instructional Symbols / Definitions
Denotes warnings that may lead to serious
physical injury or vehicle damage
Denotes cautions to be taken to avoid
physical injury or electronic component
damage
Denotes cautions to be taken to avoid
vehicle and component damage
Basic Required Tools
10mm Deep Well
Ratchet
Socket
50/50 Isopropyl
Clean Cloth Alcohol (70%) and
Water Mix
Part Weight (Gross) FMVSS 110 Compliance Information
All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed
0.53
lbs
options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a "Load
Carrying Capacity Reduced" label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying
0.24
kg
capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070 - 09003
Technical Support
Notes to the installer:
1) Read the entire Installation Instructions prior to beginning the installation of the part.
2) Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
3) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
4) NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
5) Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.
6) Record radio presets prior to disconnecting battery power, if needed.
7) Ensure the transportation fuse is set to "ON" before starting the install, if applicable.
8) Roll down the driver's window and adjust the power seats (if applicable) prior to disconnecting battery power, if needed.
9) Vehicle should be at room temperature.
10) The order of the disassembly and reassembly steps have been optimized for maximum efficiency and the correct installation of the
Remote Engine Start kit. Disassemble vehicle components (including harness connectors) and install the kit components according to
each step, as indicated. Avoid disassembling or reassembling any components in advance to prevent unnecessary labor time and/or
installation errors.
Genuine Accessories
Vehicle Model: Kona
Model Year 2018~
Part No. J9F57 AC200
Language English
Rev. Date 1/2/2019
Vehicle must be equipped with Smart Key (Push Button Start).
Ensure vehicle does NOT have Mechanical KEY.
Denotes quality processes to be checked
prior to moving to the next step
Denotes specific tools that are necessary
to complete a step
N
O
Denotes important information to be
T reviewed during the step
E
Extension Torque Wrench
Authorized dealers use: (1) 855-225-7344
Hours: M~F - 9am~5pm Pacific Standard Time
Revision Date
01/02/2019
Accessory: Remote Engine Start - Push Start
Difficulty: ( B )
Difficulty stated above reflects the minimum level of
Note:
expertise required to install the accessory:
(A) Customer
(B) Dealer Technician
(C) Master Technician or Specialist
Denotes personal protective equipment (PPEs) that
may be required for a step. Examples of safety
equipment icons noted below:
Glasses
Mask
#2 Phillips
Trim Removal Tool
Screwdriver
Gloves
Hearing Protection
Wire Cutters
Page 1 of 10