Siemens CLVD1325/5-50 Installation Instructions

CLVD1325/5-50
Order number 2GF1667-8AU
Document
Edition 02.2007
Front View
D1
D2
INTRODUCTION
Thank you for purchasing this Siemens product. Please read and follow
these instructions carefully.
MOUNT TYPE
This lens is designed for use with 1/2 inch C-mount CCD cameras
(17.526mm flange dimension). When fitting the lens to a CS-mount
camera, an adapter ring must be used to ensure correct flange position
(supplied free of charge with all Siemens cameras).
MOUNTING TO THE CAMERA
The lens is installed by screwing it clockwise into the mount on the CCTV
camera. Having screwed the lens in as far as it will go, you can rotate the
lens chassis back to suit the setup position of the camera.
IRIS
If the camera is fitted with a selection switch for Video and DC, set it to
DC.
PRODUCT SAFTY PRECAUTIONS
The following symbols appear in these safety instructions.
This symbol indicates presents of an electrical current and the
risk of electric shocks.
This symbol indicates a risk of fire.
HAZARD
Serious injury or loss of life may result from failure to comply with safety instructions in this category.
Do not disassemble the unit or try to
insert metal objects or flammable materials into it.
If the connection cable is cracked or
damaged, switch off immediately.
Do not place the unit near extreme heat,
an open flame or a source of flammable gases.
Do not expose the product to extremely
high or low temperatures. (not hotter than +60°C
or colder than -10°C). Extreme temperatures will
affect performance and may damage the product.
If you intend to connect the product to
another product, read the connection instructions
in both product manuals carefully beforehand.
A6V10062007
32 mm
24,6 mm
the connection cable.
water should penetrate the unit, switch off
immediately.
power supply
wet hands
heat sources as these could melt the insulation.
Light passing through the lens could cause a fire
if directed at a flammable material.
Installation Instructions
Side View
D1 40
D2 38,6 mm
L 59,2 mm
A 4,0
TO INSURE LONG-TERM RELIABILITY
Remove dust from the lens using a blower or soft brush. Avoid touching the
lens surface.
Use lens cleaning paper or a clean cotton cloth with a little cleaning liquid to
remove finger prints or oil stains from the lens surface. Start in the centre of
the lens and work outwards. Avoid using organic solvents such as thinner or
benzene.
SPECIFICATION
Imager Size
Focal Length
Aperture Range
Angle of View
Mount-Type
Application Temperature Range
Minimum Object Distance
This symbol means that you should not disassemble the
product.
This symbol means that you must comply with the instruction
concerned.
Do not scratch, cut open, twist or heat
Do not expose the unit to water. If
Do not try to repair the unit or the
Do not plug in or unplug the cable with
Keep the connection cable away from
Do not store a lens in direct sunlight.
Pin out connections
(Camera socket viewed from
above)
mm
Pin Function
1 Control -
mm
2 Control +
3 Driver +
4 Driver -
1/3 inch
5-50 mm
DC IRIS F 1.4 – 360
TELE
Horizontal
5,6°
Vertical
4,2°
CS-Mount
-10 - +60°C
0,3 m
Do not attempt to use the product if you
see smoke or smell burning.
Do not look into the sun through the
lens as this could cause blindness.
Keep the product out of children's
reach. If the product were to fall on a child, it
could cause serious injury.
Do not place the product near a stove
or humidifier or in any other location where there
are conditions of high heat or humidity.
Do not drop the product or expose it to
heavy impacts. This could lead to serious
damage.
English
Orange
Yellow
Red
Black
WIDE
53,6°
40,3°