Related Manuals for Nemtek FG7C
Summary of Contents for Nemtek FG7C
- Page 1 GROUP OF COMPANIES FG7C CONTROLLER for DRUID 25/28 NETWORKS INSTALLERS MANUAL Revision 1.3 11 December 2018...
-
Page 2: Table Of Contents
FG7C CONTROLLER: Table of Contents INTRODUCTION…..……………………………………………………………………… OPENING THE FG7C…...………………………………………………….……………. HARDWARE….................. INSTALLING THE FG7C…………………………………………………………………. THE DISPLAY BOARD……………………………………………………………………. COMMUNICATION BOARDS…………………………………………………………… 10-12 PROGRAMMING THE FG7C ……….……………..…………………………………… 12-16 MAPPING…………………………………………………………………………………….. 17-20 FIRMWARE UPGRADE…………………………………………………………………… THE FG7 WEB INTERFACE…………………………………………………………….. 21-22 THIRD PARTY INTEGRATION………………………………………………………… DOCUMENT REVISION HISTORY……………..…………………………………….. 23... -
Page 3: Introduction
Panel mount type On one of the long sides of the FG7C are two slots. Insert a 6.5mm screw driver into one of the slots and turn the screw driver until the lid with the display pops up on that side. Now repeat this... - Page 4 Wall mount type On one of the long sides of the FG7C are two openings with retaining clips. Insert a 6.5mm screw driver into the bottom part of one of the openings and push the retainer clip back until the lid with the display pops up on that side.
-
Page 5: Hardware
HARDWARE HARDWARE The lid of the FG7C contains a green printed circuit board IOT1711JM and a dark blue control unit as well as the touch screen. The IOT1711JM board is responsible for generating the supply voltage for the control unit as well as the display. -
Page 6: Installing The Fg7C
INSTALLING THE PANEL MOUNT FG7C The panel mount FG7C is designed to be mounted flush in wooden walls or dry walling. A cut out has to be made in these walls of 195mm x 130 mm. -
Page 7: Installing The Fg7C
FG7C CONTROLLER: Installing the FG7C FG7C CONTROLLER: Installing the communication boa If removal of the base is required then first remove the lid from the base and disconnect the wiring between the lid and the base, so that it can be fully removed. Turn the top wing clamp screw anti clockwise until the wing clamp comes back into its base cavity (do not fully unscrew the wing clamp screw since it will detach and can fall inside the wall). -
Page 8: The Display Board
SW1 “B3_RESET”. The 5V_RESET button is used to manually power the control unit on and off, this is usually required when programming the settings on the FG7C. The B3 RESET button is used to manually reset the FG7C control unit. -
Page 9: The Display Board
FG7C CONTROLLER: THE DISPLAY BOARD LED’S ON DISPLAY BOARD LED1 Shows that the FG7C is On LED2 5V supply indicator LED3 When flashing, indicates that the watchdog timer is operational LED4 Not in use CONNECTORS Con 1 Ribbon cable connection to Con1 of communication board... -
Page 10: Communication Boards
FG7C CONTROLLER: COMMUNICATION BOARDS THE NEMLINK/TAUT WIRE COMMUNICATION BOARD JUMPER SETTINGS COMMUNICATION BOARD Jumper setting as viewed with connectors at the bottom. Nemlink programming JP3 (1) Down to enable programming of the Nemlink Up standard operational mode LED’S ON COMMUNICATION BOARD... - Page 11 FG7C CONTROLLER: COMMUNICATION BOARDS THE RS485/TAUTWIRE/TTL COMMUNICATION BOARD JUMPER SETTINGS COMMUNICATION BOARD Jumper setting as viewed with connectors at the bottom. TTL Serial JP1 (2) Down if serial TTL is selected (For Nemlink communication) Up if RS 485 or RS 232 communication is required...
-
Page 12: Programming The Fg7C
The FG7C-Druid should be programmed with the number of energizers as well as the IO cards in the system. If required a graphic site image can be loaded on the FG7C-Druid and zones (sectors) as well as Gate lines can be drawn on the image. - Page 13 Otherwise one can push the B3- PWR button and this will close the application and after the Nemtek logo has disappeared from the screen you press the B3-PWR button again to restart the unit.
- Page 14 FG7C CONTROLLER: Programming the FG7C USER TAB SETTINGS Under the user tab are several buttons for setting: Installer and User PIN numbers (see user manual) Time (see user manual) Saving the Log (see user manual) Defaulting to factory settings FACTORY DEFAULT Under the USER Tab you can reset the FG7 to Factory default settings by pressing the default button the IP address will be reset to 10.0.0.20 and all pin settings will default back to the...
- Page 15 FG7 screen is to first untick AbsoluteIO on the system tab. FAILSAFE When third party software or Nemtek FenceProbe is used and the connection between the application and the FG7 is lost then the FG7 will automatically reset to enable the application to reconnect.
- Page 16 FG7C CONTROLLER: Programming the FG7C DRAWING THE ZONES AND GATES LINES 1) On the FG7, press the PIN tab on the top screen and Select ▼ Installer. Enter the appropriate PIN number and press Enter. Check that Installer stays on the screen and has no revert back to Select.
-
Page 17: Mapping
FG7C CONTROLLER Mapping MAPPING ENERGIZER ALARM(S) TO IO CARD A text file, etoimapplus.txt, i.e. energizer to io card mapping file is used to map each energizer address to a relay card address. This file can be made in notepad and has to be uploaded to the FG7 with the use of the web interface. - Page 18 FG7C CONTROLLER Mapping 2) If the relay must only be activated as long as the alarm condition persist (not latching) then select the energizer condition in table 2 and add the number together for all the relays which must not latch. Zero implies everything is latching and an alarm condition has to be reset manually after an alarm occurs.
- Page 19 MAPPING NEMTEK IO CARDS TO ENERGIZER(S) Inputs on a Nemtek IO card may be used to control a specific energizer or all i.e. global energizers on a network. A text file, itoemap.txt, i.e. io card to energizer mapping file, is used to map each IO card address to an energizer.
-
Page 20: Firmware Upgrade
FG7C CONTROLLER Mapping TABLE 4: How the numbers relate to the IO Card Inputs NUMBER INPUT INPUT FUNCTION Input 1 ZONE 1 ON/OFF Input 2 ZONE 2 ON/OFF Input 3 ZONE 1 HIGH/LOW VOLTAGE Input 4 ZONE 2 HIGH/LOW VOLTAGE... -
Page 21: The Fg7 Web Interface
FG7C CONTROLLER FG7 WEB INTERFACE THE FG7 WEB INTERFACE The FG7 has a web interface which can be used for: 1) Viewing mapping files loaded in the FG7 2) Uploading new mapping files 3) Uploading new site images 4) Switching between LCD touchscreen and HDMI display... -
Page 22: Third Party Integration
APP or TWNODE APP it can be set for use with Taut-wire sensors instead of energizers. THIRD PARTY INTEGRATION The FG7 can communicate with third party software such as Nemtek Druid FenceProbe. The communication is done through the Ethernet port on the blue control board of the FG7. -
Page 23: Document Revision History
FG7 fails then control would be given to the mapping of the inputs of the IO card(s) and not to the FG7 User (see AbsoluteIO). Please also read the section Failsafe of this manual if third party integration or Nemtek FenceProbe is used.