Dimplex DESC2T Installation And Operating Instructions

Dimplex Compact Convector Heaters
Models : DESC2T, DESC2TA, DESC2S, DESC2SA, DESC2TS & DESC2TSA
Model(s) Specification
DESC2T 2.0kw Thermostat
DESC2TA 2.0kw Thermostat
DESC2S
2.0kw Heat Switch
DESC2SA
2.0kw Heat Switch
DESC2TS 2.0kw Thermostat + Heat Switch
DESC2TSA 2.0kw Thermostat + Heat Switch
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
IMPORTANT SAFETY ADVICE
WARNING –THIS APPLIANCE MUST NOT BE USED IN A
BATHROOM
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING
POOL.
WARNING – THIS HEATER MUST NOT BE LOCATED
IMMEDIATELY BELOW A FIXED SOCKET OUTLET.
DO NOT USE THE HEATER UNTIL THE FEET OR WALL BRACKETS
ARE FITTED CORRECTLY.
FOLLOW these instructions carefully.
NEVER cover or obstruct in any way the heat outlet slots at
the top of the heater or the air inlet slots in the base of the
heater.
WARNING: In order to avoid overheating, DO NOT COVER
the heater.
The heater carries a text warning 'DO NOT COVER' and
also carries the Warning symbol
must not be covered.
In order to avoid a hazard due to inadvertant resetting of
the thermal cutout, this appliancemust not be supplied
through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off
by the utility.
This appliance is not intended for use by children or other
persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them
from using it safely. Children should be supervised to
ensure that they do not play with the appliance.
If young children, the aged or infirm are likely to be left in
the vicinity of the heater, we advise that adequate
precautions should be taken.-
We recommend that a guard be fitted to ensure contact
with the heater is avoided and objects cannot be inserted
into the product.
If the mains lead is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
For further information, please contact our guard supplier
direct on Tel. No. 01603 667957, or in case of difficulty or for
further advice contact the Customer Helpline.
Installation and Operating Instructions
Dimensions
(millimetres)
230
MIN
373
indicating that it
541
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
IMPORTANT : If the plug is not suitable for your socket, the plug
should be removed. Before wiring the appropriate plug, please note
that the wires in this mains lead are coloured in accordance with the
following code :
GREEN AND YELLOW :
BLUE :
BROWN :
Connect the GREEN AND YELLOW wire to the terminal marked 'E' or
by the earth symbol , or coloured GREEN or GREEN AND YELLOW.
Connect the BROWN wire to the terminal marked 'L' or coloured RED.
Connect the BLUE wire to the terminal marked 'N' or coloured BLACK.
General
The heater may be used free standing on feet or wall mounted on
brackets. The necessary feet and wall brackets are provided. The
heater should only be operated when in the upright position as shown
in Fig. 1 above.
To fit feet
Lay the heater on its back, and locate the foot fixing screw (see Fig.
4a). Remove the screw using an X–head screwdriver, then align the
foot over slots and holes in base (see Fig. 4c) and push into slots until
the foot clips into place.
Finally take the foot fixing screw, insert and tighten using a screwdriver
to secure the foot.
NOTE – The wall mounting brackets indicated in Fig. 4b can be left
secured to the base if they are not required.
Wall Mounting
foot fixing
brackets
screw
(a) (b)
ON NO ACCOUNT SHOULD THE HEATER BE USED FREE STANDING
WITHOUT THE FEET FITTED.
8/51923/0
500
MIN
312
230
MIN
EARTH
NEUTRAL
LIVE
(c)
Issue 0
shelf
Fig. 1
foot
pins
Fig. 2