Download
Share
Print this page
LG GCW1069CS Quick Start Manual
  1. Manuals
  2. Brands
  3. LG Manuals
  4. Washer/Dryer
  5. GCW1069CS
  6. Quick start manual
LG GCW1069CS Quick Start Manual

LG GCW1069CS Quick Start Manual

Waverider installation
Hide thumbs Also See for GCW1069CS:

Advertisement

Quick Links

Download this manual See also: Owner's Manual
WaveRider Installation
INTERNAL MOUNTING
SINGLE MACHINE
CARD ONLY
www.heartlandMicroPayments.com
2115 Chapman Road, Suite 159, Chattanooga TN 37421
800.332.4835

Advertisement

loading

Related Manuals for LG GCW1069CS

Summary of Contents for LG GCW1069CS

  • Page 1 WaveRider Installation INTERNAL MOUNTING SINGLE MACHINE CARD ONLY www.heartlandMicroPayments.com 2115 Chapman Road, Suite 159, Chattanooga TN 37421 800.332.4835...
  • Page 2 Laundry Machine Model Numbers This document applies to the WaveReader installation process following LG model numbers: Washers GCW1069CS Dryers GD1329CES If you cannot locate the model number of the machine you require in the lists above, please contact MicroPayments Customer Service at: Tel: 800-332-4835 Press 2 www.heartlandMicroPayments.com...
  • Page 3 Required Tools & Installation Kit Contents The tools required for the installation process are as follows  #T-20 Pin-in-Star Torx Driver  Phillips Head Screwdriver (medium)  Small Flat-Head Screwdriver  11/32” Ratchet or Nut Driver This following tables list the required components for the installation process. If you cannot locate and/or identify any of the components listed above, please contact MicroPayments Customer Service at 800-332-4835 , then press 2.
  • Page 4 Interface Harness Harness Kit for LG – Card Only KIT-HRN-050-6-008 Item Part Number Description ASM-050-6-008 LG Card Only Interface Cable AYS-050-6-008 Cable, Service Mode Switch - LG Internal Mounting Trim Plate Kit KIT-050-6-008 Bracket Kit for WaveReader Surface Mount Item...
  • Page 5 !! WARNING !! MAKE SURE THAT ALL POWER HAS BEEN REMOVED FROM THE MACHINE BEFORE ATTEMPTING TO INSTALL ANY HARDWARE OR CABLING! Preparation Disconnect the laundry machine from all power sources before performing any of the following steps. Only perform the following steps after the WaveReader has been physically installed in the machine.
  • Page 6 Pin-In-Star Driver. Set the screws aside keeping them close at hand. Insert the WaveReader card guide through the LG Bracket Adapter. Using the provided 6-32 Flat Head Phillips Machine Screws attach the LG Bracket Adapter onto the rear of the WaveReader in the 4 tapped holes.
  • Page 7 Installation Locate the ribbon cable connector on the Circuit Board at the rear of the WaveReader. Using your thumb nails and placing them on the wings of the small tabs, pull the slide downward as shown Gently pull the white ribbon cable out of the connector.
  • Page 8 With the WaveReader attached to the LG Adapter Bracket and the Circuit Board Removed, slide the card guide and ribbon cable through the front of the control panel as shown.
  • Page 9 Installation Using the provided 8x32 Locking Nuts, bolt in the Adapter Bracket to the Control Panel. Reattach the Circuit Board to the Card Guide using a small Phillips head screw driver. Slide the Ribbon Cable into the ribbon connector slot located on the Circuit Board.
  • Page 10 Looking down on top of the LG Controller board, in the bottom left hand corner find the connector labeled “ESUDS OUT PIN2.” Using the WaveReader Interface Cable, locate the connector with four wires attached: brown, orange, yellow, and white.
  • Page 11 Installation Keeping the wires together, flip the controller box cover back over to its original position. Replace all 4 Phillips head machine screws previously removed. Run wires through the supplied wire catch as shown. On the machine side, there will be two identical black connectors.
  • Page 12 Installation Find the mating black connector on the WaveReader Interface Cable and attach the two together. Attach the J3 (Black) connector into the mating connector on the back of the WaveReader Board as shown. The connector should snap once in place. www.heartlandMicroPayments.com...
  • Page 13 Installation On the machine side, find the white connector with blue, white, gray, brown, black, and orange wires. Plug the white connector of the Service Mode Switch Cable into the white connector on the machine side. Run the wires so that they are out of the way, but you can still reach the switch.

  • Page 14: Important Programming Notes

    Pricing is independent from the WaveRider System and is controlled by the machine. Set prices prior to final assembly of the Control Panel. Please refer to the LG Owner’s Manual provided with the machine for instructions on Setting Prices. Do NOT place the machine in card mode. Currently the WaveRider system interfaces with the machine through coin mode.
  • Page 15 Installation Place the Control Panel back into its original position, making sure all wiring harnesses are clear and out of the way Align the Control Panel with the underlying brackets and screw in the 2 (one to each side) Pin-in-Star Security screws using the #20 bit Security Driver.

  • Page 16: Finished Assembly

    Installation Finished assembly. Apply the self-adhesive sticker that displays the accepted card brands (supplied) in a clearly visible location . Once the unit has been reassembled, the entire WaveReader needs to be tested before IMPORTANT being returned to The WaveContoller has to be service.

This manual is also suitable for:

Gd1329ces