Summary of Contents for N.KO PASOVEC 75 RUNNER
- Page 1 MOBILE BELT GRINDER PASOVEC 75 RUNNER Purchase order No. 1300 – 400 V / 60 Hz Purchase order No. 13001 – 480 V / 60 Hz Purchase order No. 13002 – 220 V / 60 Hz Operating manual CHANGE RESERVED...
-
Page 2: Table Of Contents
Contents: General information Description of RUNNER machine Identification data Tests Warranties Safety regulations Technical specification Accessories Device unpacking Controls of RUNNER Maintenance and operation Spare parts List of spare parts Wiring diagram Basic dimensions Always read the operating instructions carefully before use... -
Page 3: General Information
The mobile belt grinder PASOVEC 75 RUNNER only is designed for the following activities: The mobile belt grinder PASOVEC 75 RUNNER is designed for grinding at a workshop or a production hall. This is a hand-driven machine. Only use the machine in an environment protected from rain, snow and other adverse weather conditions. -
Page 4: Identification Data
13001 – 480 V / 60 Hz 13002 – 220 V / 60 Hz 3. Identification data The identification data of the PASOVEC 75 RUNNER mobile grinder are listed on the label attached to the machine body. 4. Tests The PASOVEC 75 RUNNER mobile grinder is tested in our technical testing room. -
Page 5: Safety Regulations
The manufacturer considers the warranty invalid in the case of: • machine misuse. • use contrary to national or international standards • incorrect installation • faulty power supply • serious maintenance deficiencies • unauthorized modifications or interventions • Using other than original and factory-approved spare parts and accessories for the model in question •... - Page 6 Operator (s) must always: 1. Make sure before the machine starts that all safety covers are mounted and that the safety devices are functional. 2. Avoid wearing the type of clothing or jewellery that might be caught in moving parts. 3.
-
Page 7: Technical Specification
Unpack the machine from a wooden box and check that everything is OK and the machine is undamaged. If you have any questions, please contact your reseller. Mobile belt grinder PASOVEC 75 RUNNER is supplied: Belt grinder PASOVEC 75 RUNNER... -
Page 8: Controls Of Runner
10. Controls of the mobile belt grinder PASOVEC 75 RUNNER 1. Securing the machine in the non-working position (transport mode) 2. Power supply connection and ON/OFF control 3. Emergency switch 4. Belt centering mechanism 5. Removal adjustment mechanism... -
Page 9: Use
Always unplug the power supply before adjusting the machine. 1. Release the mechanism lever to secure the machine in the transport position (pos. 1) 2. Using the removal adjustment mechanism (pos.5), ensure that the contact wheel with the abrasive belt is slightly touching the material. Set the removal mechanism adjustment before using the machine to the position so that it has sufficient power for subsequent removal adjustment. -
Page 10: Maintenance And Operation
12. Maintenance and operation Before starting maintenance, disconnect the power supply from the socket first. Adjustment, lubrication and maintenance must be carried out when the machine is completely at rest. Pay attention to the maintenance of the drive and contact wheel. Monitor their wear and weighing. -
Page 11: Spare Parts
13. Spare parts and accessories Purchase orders for spare parts must contain the following information: • Machine type • Serial number • Description of the required part and its number • Quantity 13.1 List of spare parts... - Page 12 PART DESCRIPTION QTY Art. Nr. PART DESCRIPTION QTY Art. Nr. SUPPORT 1300_1 SUPPORTING 1300_46 ASSEMBLY PLATE JOYSTICK 1300_2 BLACK LEAD 307518/1 PLATE FIFTH WHEEL 1300_3 BEIVEN WHEEL 1300_48 GUIDE HANDLE 1300_4 HANDLE 1300_49 HANGER 1300_5 TAPER KNOB 1300_50 BEARING WHEEL 1300_6 SPRING 1300_51...
- Page 13 LOCKNUT M6 1300_27 HEXAGON 1300_72 HEADED BOLT M8X25 SCREW M4X8 1300_28 HEXAGON 1300_73 HEADED BOLT M8X20 WASHER Φ4 1300_29 BUTTON HEAD 1300_74 SCREW M8X20 NUT M4 1300_30 NUT M8 1300_75 SCREW M6X10 1300_31 BUTTON HEAD 1300_76 SCREW M4X6 HEXAGON 1300_32 INNER HEXAGON 1300_77 HEADED BOLT...
-
Page 14: Wiring Diagram
13.2 Wiring diagram 13.3 Basic dimensions and parts of the PASOVEC 75 RUNNER mobile belt grinder Control handle Engine Grinder body Contact wheel travel... - Page 15 A copy of this manual comes with each RUNNER machine. All rights reserved. No part of this publication may be reproduced without the prior consent of N.KO N.KO spol. s r.o. Táborská 398/22 293 01 Mladá Boleslav The Czech Republic phone: +420 326 772 001 nko@nko.cz...