Toshiba SG-1981 Owner's Manual page 50

QUICK
REFERENCE CALLER ID CORDLESS TELEPHONE
DIGITAL ANSWERING SYSTEM
GUIDE
SG-1981
Read the Owner's Manual for details.
SETTING UP THE BASE UNIT
Fasten the AC
Raise the antenna to vertical adaptor cord.
position.
Telephone Line Cord Single-Line
Telephone Jack
(RJ11C)
Power Outlet
NOTE: Plug the AC adaptor firmly
(AC 120V, 60Hz)
into the base unit and the AC
AC Adaptor
120V outlet.
CHARGING THE BATTERY PACK
1
Remove the battery cover by sliding it down.
Black Red
2
Plug the battery pack cord into its socket, observing
the correct polarity.
3
Place the battery pack . Then close the battery
compartment cover.
4
Place the handset on the base unit. You can place
the handset with the dialpad facing up or down.
IMPORTANT
Charge the battery pack for at least 12 to 16 hours.
CHARGE
LED
Charging contacts
UCZZ69739BZ RC009821 Printed in China
SETTING / USING THE PHONE
Setting The Tone/Pulse Switch
Set the TONE/PULSE switch to TONE.
Place a call.
If the call does not connect with the TONE setting, set the
TONE/PULSE switch to PULSE
TONE/PULSE switch
Area Code
1
Press FUNCTION , then press 3 .
2
Press SELECT/CHANNEL and enter your 3-digit area
code.
3
Press SELECT/CHANNEL , then press .
FUNCTION
Making a Call
1
Dial the phone number.
FLASH
2
Press TALK .
CID
TALK
3
Press TALK to hang up.
L.D. LOCAL
3
TONE
TONE/
Answering a Call RDL/P FUNCTION SELECT DELETE
FUNCTION
SELECT/CHANNEL
With the handset
Press TALK and speak.
NOTE: To indicate Caller ID data, let the
phone ring twice before you answer the call.
With the base speaker phone
1
Press and speak.
SPEAKER
2
Press SPEAKER to hang up.
SPEAKER
CALLER ID SERVICE
Setting Up Caller ID
To use Caller ID/Caller ID on Call Waiting ,
features, you must subscribe to both Caller
CID
ID/Caller ID on Call Waiting services provided MEM
CID
by your local telephone company.
FLASH
TALK
L.D. LOCAL
1 3
TONE
RDL/P FUNCTION SELECT DELETE
DELETE
FUNCTION
SELECT/CHANNEL
Making a Call with Caller ID Data
1
Press CID , then press or to display the number you want to dial.
2
Press TALK , then the displayed number will be dialed.
Note: For long distance calls, you need a prefix "1" and the area code.
Press L.D./1 and LOCAL/3 to add or cancel "1" and the area code
before you press TALK .
Storing Caller ID Data to Speed-Dial Memory
1
Press CID , then press or to display the number you want to store into
Speed-dial memory.
2
Press MEM , then press , or enter a memory location number.
3
Press SELECT/CHANNEL . A confirmation beep sounds and the Caller ID data is
stored.
Press CID to return to standby mode.
Deleting Caller ID Data
1
Press CID , then press or to display the Caller ID number you want to
delete from the memory.
2
Press DELETE , then press or to select Yes or No.
3
Press SELECT/CHANNEL or DELETE .
4
Press CID to return to standby mode.
ANSWERING MACHINE
LED Display
SPEAKER DELETE
PLAY/STOP
VOLUME/+
VOLUME DELETE
PLAY
VOLUME/– MEMO/2WAY REC
STOP
MEMO
GREETING 2 WAY REC
REPEAT
SKIP
GREETING
ANSWER PAGE
ANSWER
PIN TIME
TIME
PIN
SPEAKER
Turning the Answering Machine ON/OFF
Press to turn the answering machine on or off.
ANSWER
Every time you press , the LED display turns on or off.
ANSWER
Setting the Clock
1
Press and hold TIME till a beep sounds.
2
Select the day of the week by pressing REPEAT or SKIP .
When the correct day is announced, press TIME .
3
Select the hour by pressing REPEAT or SKIP .
When the correct hour is announced, press TIME .
4
Select the minute by pressing REPEAT or SKIP .
TIME
When the correct minute is announced, press .
5
Select AM/PM by pressing REPEAT or SKIP .
When AM or PM is announced, press TIME .
Recording and Setting the Greeting Message
To record the greeting message:
1
Press and hold GREETING till a beep sounds.
2
Record your message over the microphone.
3
Press GREETING or PLAY/STOP to finish recording.
To change the greeting message:
1
Press GREETING in the standby mode.
2
During playback, press GREETING again to switch the greeting message.
3
Press PLAY/STOP to exit the system.
Setting the Security code (PIN)
1
Press and hold PIN till a beep sounds in the standby mode.
2
SKIP
Press REPEAT or to select the left digit of the PIN.
When your desired number appears on the LED display, press PIN .
3
Press REPEAT or SKIP to select the right digit of the PIN.
When your desired number appears on the LED display, press .
PIN
Playing Recorded Messages
To playback the message Press PLAY/STOP .
To repeat the previous message Press REPEAT (within 2 seconds after the
beginning of message).
To repeat the current message Press REPEAT (after 2 seconds after the
beginning of message).
To skip the message. Press SKIP .
To go backward and repeat a Press and hold REPEAT until your desired
message you choose message number appears on the display during
playback of the message.
To delete a message Press DELETE during playback of the message
you want to delete.
To go forward Press and hold SKIP until your desired message
number appears on the display during playback of
the message.
To stop playback Press PLAY/STOP
To delete all messages Finish the playback of all messages. Then, press
and hold DELETE till a beep sounds.
To adjust the speaker volume (1-10) Press VOLUME/+ or VOLUME/– repeatedly
For more detailed instructions and examples, please refer to the owner's manual.