1. Manuals
  2. Brands
  3. Dell Manuals
  4. Laptop
  5. Vostro 3490
  6. Service manual

Dell Vostro 3490 Service Manual

Hide thumbs Also See for Vostro 3490:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
Dell Vostro 3490
Service Manual
Regulatory Model: P89G
Regulatory Type: P89G005

Advertisement

Table of Contents
loading

Related Manuals for Dell Vostro 3490

Summary of Contents for Dell Vostro 3490

  • Page 1 Dell Vostro 3490 Service Manual Regulatory Model: P89G Regulatory Type: P89G005...
  • Page 2 A WARNING indicates a potential for property damage, personal injury, or death. © 2018 - 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

  • Page 3: Table Of Contents

    Contents 1 Working on your computer......................6 Safety instructions.................................6 Before working inside your computer........................... 6 Electrostatic discharge—ESD protection........................7 ESD field service kit ................................ 7 Transporting sensitive components..........................8 After working inside your computer..........................8 2 Removing and installing components..................... 9 Recommended tools................................9 Screw list....................................
  • Page 4 Removing the heatsink - discrete..........................34 Installing the heatsink - discrete..........................35 VGA Daughterboard................................36 Removing the VGA daughterboard..........................36 Installing the VGA daughterboard..........................37 Speakers....................................38 Removing the speakers..............................38 Installing the speakers..............................40 IO board....................................41 Removing the IO board..............................41 Installing the IO board..............................43 Touchpad....................................44 Removing the touch pad assembly..........................
  • Page 5 Enhanced Pre-Boot System Assessment (ePSA) diagnostics..................93 Running the ePSA diagnostics.............................93 System diagnostic lights..............................93 Flashing BIOS (USB key)..............................94 Flashing the BIOS................................94 Backup media and recovery options..........................95 WiFi power cycle................................. 95 Flea power release................................95 5 Getting help..........................96 Contacting Dell..................................96 Contents...

  • Page 6: Working On Your Computer

    Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

  • Page 7: Electrostatic Discharge-Esd Protection

    Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

  • Page 8: Transporting Sensitive Components

    Transporting sensitive components When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

  • Page 9: Removing And Installing Components

    Removing and installing components Recommended tools The procedures in this document require the following tools: • Phillips #0 screwdriver • Phillips #1 screwdriver • Plastic scribe NOTE: The #0 screw driver is for screws 0-1 and the #1 screw driver is for screws 2-4 Screw list The table provides the list of screws that are used for securing different components.

  • Page 10: Secure Digital Card

    Component Screw type Quantity Screw image Optical-drive connector board M2x2 Big Head Power-adapter port M2x2 Power-button board M2x3 Power button with fingerprint M2x2 reader (optional) Solid-state drive M2x2 Solid-state drive M2x3 System board M2x4 Touchpad M2x2 Wireless-card bracket M2x3 Secure Digital Card Removing the Secure Digital card Prerequisites 1.

  • Page 11: Installing The Secure Digital Card

    Installing the Secure Digital card Steps 1. Slide the secure digital into the slot until it clicks into place. 2. Follow the procedures in After working inside your computer. Removing and installing components...

  • Page 12: Base Cover

    Base cover Removing the base cover Prerequisites 1. Follow the procedure in before working inside your computer 2. Remove the SD memory card Steps 1. Loosen the three captive screws [1]. 2. Remove the six (M2.5x6) screws that secure the base cover to the palmrest and keyboard assembly [2]. Removing and installing components...
  • Page 13 3. Pry the base cover from the top-right corner [1] and continue to open the right side of the base cover [2]. 4. Lift the left side of the base cover and remove it off the system [3]. Removing and installing components...

  • Page 14: Installing The Base Cover

    Installing the base cover Steps 1. Place the base cover on the palmrest and keyboard assembly [1]. 2. Press the right side of the base cover until it snaps into place [2, 3]. 3. Tighten the three captive screws and replace the six (M2.5x6) screws that secure the base cover to the palmrest and keyboard assembly [1, 2].

  • Page 15: Battery

    If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for assistance. See www.dell.com/contactdell.

  • Page 16: Removing The Battery

    Removing the battery Prerequisites 1. Follow the procedure in before working inside your computer 2. Remove the SD memory card 3. Remove the base cover Steps 1. Disconnect the battery cable from the system board [1]. 2. Remove the four (M2x3) screws that secure the battery to the palmrest and keyboard assembly [2]. 3.

  • Page 17: Memory Modules

    Next steps 1. Replace the base cover 2. Replace the SD memory card 3. Follow the procedure in after working inside your computer Memory modules Removing the memory module Prerequisites 1. Follow the procedure in before working inside your computer 2.

  • Page 18: Installing The Memory Module

    Installing the memory module Steps 1. Align the notch on the memory module with the tab on the memory-module slot. 2. Slide the memory module firmly into the slot at an angle [1]. 3. Press the memory module down until the clips secure it [2]. NOTE: If you do not hear the click, remove the memory module and reinstall it.

  • Page 19: Wlan Card

    Next steps 1. Connect the battery cable to the connector on the system board. 2. Replace the base cover 3. Replace the SD memory card 4. Follow the procedure in after working inside your computer WLAN card Removing the WLAN card Prerequisites 1.

  • Page 20: Installing The Wlan Card

    Installing the WLAN card About this task CAUTION: To avoid damage to the WLAN card, do not place any cables under it. Steps 1. Insert the WLAN card into the connector on the system board [1]. 2. Connect the WLAN cables to the connectors on the WLAN card [2]. 3.

  • Page 21: Solid-State Drive/Intel Optane

    Next steps 1. Connect the battery cable to the connector on the system board. 2. Replace the base cover 3. Replace the SD memory card 4. Follow the procedure in after working inside your computer Solid-state drive/Intel Optane Removing the M.2 2230 Solid-state drive Prerequisites 1.

  • Page 22: Installing The M.2 2230 Solid-State Drive

    4. Turn the thermal plate over. 5. Remove the single (M2x2) screw that secures the solid-state drive to the thermal plate [1]. 6. Lift the solid-state drive off the thermal plate [2]. Installing the M.2 2230 Solid-state drive Steps 1. Place the solid-state drive into the thermal plate slot [1]. 2.
  • Page 23 3. Align the notch on the solid-state drive with the tab on the solid-state drive slot. 4. Slide and insert the tab of the solid-state drive into the solid-state drive slot [1, 2]. 5. Tighten the captive screw that secures the thermal plate to the palmrest and keyboard assembly [3]. 6.

  • Page 24: Removing The M.2 2280 Solid-State Drive Or Intel Optane Memory - Optional

    Removing the M.2 2280 Solid-state drive or Intel Optane memory - Optional Prerequisites 1. Follow the procedure in before working inside your computer 2. Remove the SD memory card 3. Remove the base cover 4. Disconnect the battery cable from the connector on the system board. Steps 1.

  • Page 25: Coin-Cell Battery

    Next steps 1. Connect the battery cable to the connector on the system board. 2. Replace the base cover 3. Replace the SD memory card 4. Follow the procedure in after working inside your computer Coin-cell battery Removing the coin-cell Prerequisites 1.

  • Page 26: Hard Drive

    Next steps 1. Connect the battery cable to the connector on the system board. 2. Replace the base cover 3. Replace the SD memory card 4. Follow the procedure in after working inside your computer Hard drive Removing the hard drive assembly Prerequisites 1.
  • Page 27 4. Disconnect the interposer from the hard drive. 5. Remove the four (M3x3) screws that secure the hard drive bracket to the hard drive [1]. 6. Lift the hard drive bracket off the hard drive [2]. Removing and installing components...

  • Page 28: Installing The Hard Drive Assembly

    Installing the hard drive assembly Steps 1. Align the screw holes on the hard drive bracket with the screw holes on the hard drive [1]. 2. Replace the four (M3x3) screws that secure the hard drive bracket to the hard drive [2]. 3.
  • Page 29 4. Align the screw holes on the hard drive assembly with the screw holes on the palm rest and keyboard assembly [1]. 5. Replace the four (M2x3) screws that secure the hard drive assembly to the palm rest and keyboard assembly [2]. 6.

  • Page 30: System Fan

    System fan Removing the system fan Prerequisites 1. Follow the procedure in before working inside your computer 2. Remove the SD memory card 3. Remove the base cover 4. Disconnect the battery cable from the connector on the system board. 5.

  • Page 31: Installing The System Fan

    Installing the system fan Steps 1. Align the screw holes on the fan with the screw holes on the palm rest and keyboard board assembly [1]. 2. Replace the two (M2x5) screws that secure the fan to the palm rest and keyboard board assembly [2]. Removing and installing components...
  • Page 32 3. Route the display cable through the routing guides on the fan [1]. 4. Connect the display cable and fan cable to the system board [2, 3]. Next steps 1. Replace the hard drive assembly 2. Replace the battery Removing and installing components...

  • Page 33: Heat Sink

    3. Replace the base cover 4. Replace the SD memory card 5. Follow the procedure in after working inside your computer Heat sink Removing the heatsink - UMA Prerequisites 1. Follow the procedure in before working inside your computer 2. Remove the SD memory card 3.

  • Page 34: Removing The Heatsink - Discrete

    2. In sequential order (as indicated on the heatsink), tighten the four captive screws that secure the heatsink to the system board [2]. Next steps 1. Connect the battery cable to the connector on the system board. 2. Replace the hard drive assembly 3.

  • Page 35: Installing The Heatsink - Discrete

    Installing the heatsink - discrete Steps 1. Place the heatsink on the system board and align the screw holes on the heatsink with the screw holes on the system board [1]. 2. Replace the three (M2x3) screws that secure the heatsink to the system board [2]. 3.

  • Page 36: Vga Daughterboard

    Next steps 1. Connect the battery cable to the connector on the system board. 2. Replace the base cover 3. Replace the SD memory card 4. Follow the procedure in after working inside your computer VGA Daughterboard Removing the VGA daughterboard Prerequisites 1.

  • Page 37: Installing The Vga Daughterboard

    Installing the VGA daughterboard Steps 1. Place the VGA daughterboard and align the screw holes on the VGA daughterboard with the screw holes on the palm rest and keyboard assembly [1]. 2. Replace the two (M2x3) screws that secure the VGA daughterboard on the palm rest and keyboard assembly [2]. 3.

  • Page 38: Speakers

    Next steps 1. Connect the battery cable to the connector on the system board. 2. Replace the base cover 3. Replace the SD memory card 4. Follow the procedure in after working inside your computer Speakers Removing the speakers Prerequisites 1.
  • Page 39 3. Lift the speakers, along with the cable, off the palm rest and keyboard assembly [3]. Removing and installing components...

  • Page 40: Installing The Speakers

    Installing the speakers About this task NOTE: If the rubber grommets are pushed out when removing the speakers, push them back in before replacing the speakers. Steps 1. Using the alignment posts and rubber grommets, place the speakers in the slots on the palm rest and keyboard assembly [1]. 2.

  • Page 41: Io Board

    Next steps 1. Replace the M.2 SSD 2. Replace the battery 3. Replace the base cover 4. Replace the SD memory card 5. Follow the procedure in after working inside your computer IO board Removing the IO board Prerequisites 1. Follow the procedure in before working inside your computer 2.
  • Page 42 4. Remove the two (M2x4) screws that secure the I/O board to the palm rest and keyboard assembly [1]. 5. Lift the I/O board, along with the cable, off the palm rest and keyboard assembly [2]. Removing and installing components...

  • Page 43: Installing The Io Board

    Installing the IO board Steps 1. Using the alignment posts, place the I/O board on the palm rest and keyboard assembly [1]. 2. Replace the two (M2x4) screws that secure the I/O board to the palm rest and keyboard assembly [2]. 3.

  • Page 44: Touchpad

    Next steps 1. Replace the speakers 2. Replace the battery 3. Replace the base cover 4. Replace the SD memory card 5. Follow the procedure in after working inside your computer Touchpad Removing the touch pad assembly Prerequisites 1. Follow the procedure in before working inside your computer 2.
  • Page 45 3. Open the latch and disconnect the touch pad cable from the system board [1]. 4. Peel the tape that secures the touch pad to the palmrest and keyboard assembly [2]. 5. Remove the four (M2x2) screws that secure the touch pad to the palmrest and keyboard assembly [1]. 6.

  • Page 46: Installing The Touch Pad Assembly

    Installing the touch pad assembly About this task NOTE: Ensure that the touch pad is aligned with the guides available on the palm-rest and keyboard assembly, and the gap on either sides of the touch pad is equal. Steps 1. Place the touch pad into the slot on the palmrest and keyboard assembly [1]. 2.
  • Page 47 3. Adhere the tape that secures the touch pad to the palmrest and keyboard assembly [1]. 4. Slide the touch pad cable into its connector on the system board and close the latch to secure the cable [2]. 5. Place the touch pad bracket into the slot on the palmrest and keyboard assembly [1]. 6.

  • Page 48: Display Assembly

    Next steps 1. Replace the battery 2. Replace the base cover 3. Replace the SD memory card 4. Follow the procedure in after working inside your computer Display assembly Removing the display assembly Prerequisites 1. Follow the procedure in before working inside your computer 2.
  • Page 49 4. Remove the four (M2.5x6) screws that secure the left and right hinges to the system board, and palmrest and keyboard assembly. Removing and installing components...
  • Page 50 5. Lift the palmrest and keyboard assembly at an angle. 6. Slide and remove the palmrest and keyboard assembly off the display assembly. 7. After performing all the preceding steps, you are left with display assembly. Removing and installing components...

  • Page 51: Installing The Display Assembly

    Installing the display assembly About this task NOTE: Ensure that the hinges are opened to the maximum before replacing the display assembly on the palmrest and keyboard assembly. Steps 1. Align and place the palmrest and keyboard assembly under the hinges on the display assembly [1]. 2.
  • Page 52 3. Replace the four (M2.5x6) screws that secure the left and right hinges to the system board, and palmrest and keyboard assembly. 4. Route the display cable through the routing guides on the palmrest and keyboard assembly [1, 2]. 5. Connect the display cable to the connector on the system board [3]. Removing and installing components...

  • Page 53: Power-Button Board

    6. Affix the antenna cables to the system board [4]. Next steps 1. Replace the hard drive assembly 2. Replace the WLAN 3. Connect the battery cable to the connector on the system board. 4. Replace the base cover 5. Replace the SD memory card 6.

  • Page 54: Installing The Power Button Board

    Steps 1. Open the latch and disconnect the power button board cable from the system [1]. 2. Peel the power button cable off the palmrest and keyboard assembly [2]. 3. Remove the two (M2x3) screws that secure the power button board to the palmrest and keyboard assembly [3]. 4.

  • Page 55: Power Button

    Next steps 1. Replace the display assembly 2. Replace the hard drive assembly 3. Replace the VGA daughterboard 4. Replace the system fan 5. Replace the WLAN 6. Connect the battery cable to the connector on the system board. 7. Replace the base cover 8.

  • Page 56: Installing The Power Button

    10. Remove the power button board Steps Lift the power button off the palmrest and keyboard assembly. Installing the power button Steps Using the alignment posts, align and place the power button on the palmrest and keyboard assembly. Removing and installing components...

  • Page 57: System Board

    Next steps 1. Replace the power button board 2. Replace the display assembly 3. Replace the hard drive assembly 4. Remove the system fan 5. Replace the VGA daughterboard 6. Replace the WLAN 7. Connect the battery cable to the connector on the system board. 8.
  • Page 58 Steps 1. Disconnect the following cables from the system board: a) Power adapter port cable [1]. b) Power cable [2]. c) IO board cable [3]. d) Touchpad cable [4]. e) Keyboard cable [5]. f) Speaker cable [6]. 2. Remove the single (M2x4) screw that secures the system board to the palmrest and keyboard assembly [1]. 3.
  • Page 59 4. Disconnect the VGA daughterboard cable from the system board [1]. 5. Lift the system board off the palm-rest and keyboard assembly [2]. Removing and installing components...

  • Page 60: Installing The System Board

    Installing the system board Steps 1. Connect the VGA daughterboard cable to the system board [1]. 2. Flip and place the system board on the palmrest and keyboard assembly [2]. 3. Align the screw hole on the system board with the screw hole on the palmrest and keyboard assembly [1]. 4.
  • Page 61 5. Connect the following cables to the system board: a) Speaker cable [1]. b) Keyboard cable [2]. c) Touchpad cable [3]. d) IO board cable [4]. e) Power cable [5]. f) Power adapter port cable [6]. Removing and installing components...

  • Page 62: Power-Adapter Port

    Next steps 1. Replace the power button board 2. Replace the display assembly 3. Replace the heatsink 4. Replace the system fan 5. Replace the hard drive assembly 6. Replace the 7. Replace the WLAN 8. Replace the battery 9. Replace the base cover 10.

  • Page 63: Installing The Power Adapter Port

    6. Remove the WLAN 7. Remove the 8. Remove the hard drive assembly 9. Remove the system fan 10. Remove the heatsink 11. Remove the display assembly 12. Remove the power button board 13. Remove the system board Steps 1. Remove the single (M2x3) screw that secures the power adapter port to the palmrest and keyboard assembly [1]. 2.

  • Page 64: Display Bezel

    Next steps 1. Remove the system board 2. Replace the power button board 3. Replace the display assembly 4. Replace the hard drive assembly 5. Replace the system fan 6. Replace the heatsink 7. Replace the 8. Replace the memory 9.
  • Page 65 4. Disconnect the battery cable from the connector on the system board 5. Remove the memory 6. Remove the WLAN 7. Remove the 8. Remove the hard drive assembly 9. Remove the system fan 10. Remove the heatsink 11. Remove the display assembly Steps 1.

  • Page 66: Installing The Display Bezel

    Installing the display bezel Steps 1. Align the display bezel with the display back-cover and antenna assembly, and then gently snap the display bezel into place [1, 2]. Removing and installing components...
  • Page 67 2. Insert the tabs on the display-hinge cover to the slots on the display back-cover and antenna assembly. 3. Snap the display-hinge cover into place. Removing and installing components...

  • Page 68: Camera

    Next steps 1. Replace the display assembly 2. Replace the hard drive assembly 3. Replace the system fan 4. Replace the heatsink 5. Replace the 6. Replace the WLAN 7. Replace the memory 8. Connect the battery cable to the connector on the system board. 9.

  • Page 69: Installing The Camera

    6. Remove the 7. Remove the hard drive assembly 8. Remove the system fan 9. Remove the heatsink 10. Remove the display assembly 11. Remove the display bezel Steps 1. Using a plastic scribe, gently pry the camera off the display back-cover and antenna assembly [1]. 2.

  • Page 70: Display Panel

    Next steps 1. Replace the display bezel 2. Replace the display assembly 3. Replace the hard drive assembly 4. Replace the system fan 5. Replace the heatsink 6. Replace the 7. Replace the WLAN 8. Replace the battery 9. Replace the base cover 10.
  • Page 71 6. Remove the 7. Remove the hard drive assembly 8. Remove the system fan 9. Remove the heatsink 10. Remove the display assembly 11. Remove the display bezel 12. Remove the camera Steps 1. Remove the four (M2x2) screws that secure the display panel to the display back-cover and antenna assembly [1]. 2.

  • Page 72: Installation Display Panel

    Installation display panel Steps 1. Connect the display cable to the connector at the back of the display panel and close the latch to secure the cable [1]. 2. Adhere the tape that secures the display cable to the back of the display panel [2]. Removing and installing components...
  • Page 73 3. Turn the display panel over and place it on the display back-cover and antenna assembly [3]. 4. Align the screw holes on the display panel with the screw holes on the display back-cover and antenna assembly [1]. 5. Replace the four (M2x2) screws that secure the display panel to the display back-cover and antenna assembly [2]. Removing and installing components...

  • Page 74: Display Hinges

    Next steps 1. Replace the camera 2. Replace the display bezel 3. Replace the display assembly 4. Replace the hard drive assembly 5. Replace the system fan 6. Replace the heatsink 7. Replace the 8. Replace the WLAN 9. Replace the battery 10.

  • Page 75: Installing The Display Hinges

    5. Remove the WLAN 6. Remove the 7. Remove the hard drive assembly 8. Remove the system fan 9. Remove the heatsink 10. Remove the display assembly 11. Remove the display bezel 12. Remove the camera 13. Remove the display panel Steps 1.

  • Page 76: Display Cable

    Next steps 1. Replace the display panel 2. Replace the camera 3. Replace the display bezel 4. Replace the display assembly 5. Replace the hard drive assembly 6. Replace the system fan 7. Replace the heatsink 8. Replace the 9. Replace the WLAN 10.

  • Page 77: Installing The Display Cable

    5. Remove the WLAN 6. Remove the 7. Remove the hard drive assembly 8. Remove the system fan 9. Remove the heatsink 10. Remove the display assembly 11. Remove the display bezel 12. Remove the camera 13. Remove the display panel 14.

  • Page 78: Display Back-Cover And Antenna Assembly

    Next steps 1. Replace the display hinges 2. Replace the display panel 3. Replace the camera 4. Replace the display bezel 5. Replace the display assembly 6. Replace the hard drive assembly 7. Replace the system fan 8. Replace the heatsink 9.
  • Page 79 3. Remove the base cover 4. Remove the battery 5. Remove the WLAN 6. Remove the 7. Remove the hard drive assembly 8. Remove the system fan 9. Remove the heatsink 10. Remove the display assembly 11. Remove the display bezel 12.

  • Page 80: Installing The Display Back-Cover

    Installing the display back-cover About this task Place the display back-cover on a clean and flat surface. Next steps 1. Replace the display cable 2. Replace the display hinges 3. Replace the display panel 4. Replace the camera 5. Replace the display bezel 6.

  • Page 81: Palm-Rest And Keyboard Assembly

    Palm-rest and keyboard assembly Removing the palmrest and keyboard assembly Prerequisites 1. Follow the procedure in before working inside your computer 2. Remove the SD memory card 3. Remove the base cover 4. Remove the battery 5. Remove the memory 6.
  • Page 82 Removing and installing components...

  • Page 83: System Setup

    Boot menu Press <F12> when the Dell logo appears to initiate a one-time boot menu with a list of the valid boot devices for the system. Diagnostics and BIOS Setup options are also included in this menu. The devices listed on the boot menu depend on the bootable devices in the system.

  • Page 84: System Setup Options

    System setup options NOTE: Depending on the and its installed devices, the items listed in this section may or may not appear. General options Table 2. General Option Description System Information Displays the following information: • System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership Tag, Ownership Date, Manufacture Date, and the Express Service Code.

  • Page 85: Video

    Option Description Drives Allows you to enable or disable the various drives on-board: • SATA-0 (enabled by default) • SATA-1 (enabled by default) • SATA-2 (enabled by default) • M.2 PCIe SSD-0 (enabled by default) Smart Reporting This field controls whether hard drive errors for integrated drives are reported during system startup.

  • Page 86: Secure Boot

    Option Description Password Change This option lets you determine whether changes to the System and Hard Disk passwords are permitted when an administrator password is set. Allow Non-Admin Password Changes - This option is enabled by default. Non-Admin Setup Changes Determines whether changes to the setup option are permitted when an administrator password is set.

  • Page 87: Intel Software Guard Extensions

    Option Description Secure Boot Mode Allows you to modify the behavior of Secure Boot to allow evaluation or enforcement of UEFI driver signatures. • Deployed Mode (default) • Audit Mode Expert key Management Allows you to manipulate the security key databases only if the system is in Custom Mode. The Enable Custom Mode option is disabled by default.

  • Page 88: Power Management

    Option Description Intel SpeedStep Allows you to enable or disable the Intel SpeedStep mode of processor. • Enable Intel SpeedStep This option is set by default. C-States Control Allows you to enable or disable the additional processor sleep states. • C states This option is set by default.

  • Page 89: Post Behavior

    Adaptive—enabled by default Configuration • Standard—Fully charges your battery at a standard rate. • ExpressCharge—The battery charges over a shorter time using Dell’s fast charging technology. • Primarily AC use • Custom If Custom Charge is selected, you can also configure Custom Charge Start and Custom Charge Stop.

  • Page 90: Virtualization Support

    Virtualization support Option Description Virtualization This field specifies whether a virtual Machine Monitor (VMM) can utilize the conditional hardware capabilities provided by Intel Virtualization Technology. Enable Intel Virtualization Technology—enabled by default. VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware capabilities provided by Intel®...

  • Page 91: System Logs

    System logs Option Description BIOS Events Allows you to view and clear the System Setup (BIOS) POST events. Thermal Events Allows you to view and clear the System Setup (Thermal) events. Power Events Allows you to view and clear the System Setup (Power) events. SupportAssist System Resolution Option Description...

  • Page 92: Deleting Or Changing An Existing System Setup Password

    • The password can contain the numbers 0 through 9. • Only lower case letters are valid, upper case letters are not allowed. • Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`). 3.

  • Page 93: Troubleshooting

    Running the ePSA diagnostics Steps 1. Turn on your computer. 2. As the computer boots, press the F12 key as the Dell logo appears. 3. On the boot menu screen, select the Diagnostics option. 4. Click the arrow at the bottom left corner.

  • Page 94: Flashing Bios (Usb Key)

    4. Connect the bootable USB drive to the computer that needs the BIOS update. 5. Restart the computer and press F12 when the Dell logo is displayed on the screen. 6. Boot to the USB drive from the One Time Boot Menu.

  • Page 95: Backup Media And Recovery Options

    Backup media and recovery options It is recommended to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes multiple options for recovering Windows operating system on your Dell PC. For more information. see Dell Windows Backup Media and Recovery Options.

  • Page 96: Getting Help

    About this task Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: Steps 1.

Table of Contents