ADEMCO 612 Installation Instructions

MARGIN LINES INDICATE PRINCIPAL CHANGES IN THIS 4/87 ISSUE
0 0
TERMINALS
1 & 2
(Burglary,
Input)
1 & 4
(Burglary
or panic,
Dry Closure)
(Fire,
Input)
3 & 4
(Fire,
Closure)
5
(Abort)
(Line
Seizure)
7
(Non-Abort)
(Telephone
Line)
RED 81 BLACK
LEADS
(Power)
GREEN LEAD
(Ground)
TEST SWITCHES
A
I
T
4
5
3
0 0 0
OBSERVE POLARITY WHEREVER NOTED ABOVE
When a output is used to activate the burglary channel, connect dialer terminals 1
terminals of any Ademco control. Any voltage between
the dialer. Be sure to OBSERVE PROPER POLARITY: positive (+) to terminal 1, negative (-) to terminal
When a contact closure is used to activate the burglary channel, connect dialer terminals 1
normally open device, Any closure, either momentary (of at least 0.5 seconds duration) or lock-in, across
terminals 1 4 will activate the dialer. Devices for 24-hour hold-up or emergency protection should use
these terminals. If a 6V input is used on terminals 1
4.
When a input is used to activate the fire channel, connect dialer terminals 2
nals of the control. Any voltage between
PROPER POLARITY: negative (-) to terminal 2, positive +) to terminal 3.
When a contact closure is used to activate the fire channel, connect dialer terminals 3
mally open device. Any closure, either momentary (of at least 0.5 seconds duration) or lock-in, across
terminals 3 4 will activate the dialer. If a 6V input is used on terminals 2
be used on terminals 3 4.
If you wish to prevent (abort) the dialer from continuing to make outgoing calls once the local control or
lock-in activating device has been restored to normal, move the spade lug on the BLACK flying lead from
terminal 7 to terminal 5. The dialer will then continue to run until it is completely RESET, but will be
automatically disconnected from the telephone line and no further calls will be made. Once the dialer has
RESET, it will be automatically reconnected to the telephone line and will be ready to report a subse-
quent alarm.
If line seizure is desired (disconnects all telephones from the line when the dialer is activated, to prevent
possible interruption of the message) connect terminals 6
620 Direct Connect Cord is used to connect to telephone line and handsets. See No. 620's instructions.
If you wish the dialer to complete all of its calls, even if the activating device is RESET, or if the dialer is
operated by a momentary contact device, leave the spade lug of the BLACK flying
terminal 7.
Connect terminals 8 (TIP) and 10 (RING) to the telephone line, via a No. 620 Direct Cord, or, when local
regulations permit, via a standard four pin plug or directly to the line. If line seizure is
a No. 663 Line Seizure Module and No. 620 (see No. 620's instructions).
Connect ONLY to a 6V battery or an Ademco rechargeable
96,487 or 497). The Ademco No. 89 Energy Pack may not be used. OBSERVE POLARITY: red lead to
positive black lead to negative (-).
For protection of the circuitry against telephone line induced transients, connect to a good earth ground.
(A cold water pipe or electrical box may be used in some locations.)
Additional transient protection can be provided by a No. 255 Lightning Protector which connects directly
across the telephone line and to ground.
A No. 663 used for line seizure also provides transient protection for the No. 612 by isolating its circuitry
completely from the telephone line. In this case, a No. 255 may be installed across the telephone line
entering the No. 663 for protection of the Nos. 663 and 612.
DISCONNECTED FROM
PHONE LINES FOR
TEST SPEAKER
I
7 8
0 0 0
and 14V to dialer terminals 1
2, a contact closure cannot be used on terminals 1
and 14V will activate the dialer. Be sure to OBSERVE
7 to a No. 663 Line Seizure Module. A No.
DIALER
USED
9 10
0 0
2 to the bell
will activate
4 to any
3 to the bell termi-
4 to any nor-
3, a contact closure cannot
connected to
filtered power supply (suggested:
via
Nos.