Page 2
This product contains sensitive electrical components that may be damaged by electrical spikes,surges,electric shock,lightning strikes, etc. Use of surge proctection system is highly recommended in order to protect and extend the life of your equipment. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Page 3
Install this device in a secure location where it cannot be easily pushed or knocked over. Use of this device is not suitable for use within 6 ft. of a medical patient. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
TABLE OF CONTENTS PRODUCT DESCRIPTION OPERATION CONTROL AND FUNCTIONS FRONT/REAR PANEL RS-232 SERIAL CONTROL RS-232 & TELNET COMMANDS WEB GUI CONTROL CONNECTION DIAGRAM SPECIFICATIONS SERVICE PROCEDURE REPLACEMENT POLICY RETURN AND REPAIR SERVICE LIMITED WARRANTY 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
1- 3.5mm to 9-pin D-sub Adapter Cable • 1- User Manual SYSTEM REQUIREMENTS 5V, 12V, 24V or 48V powered equipment requiring less than 15 watts of power using 2-pin 3.5mm terminal block terminated power cables. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Press and hold this button for 5+ seconds, after the unit is already powered on, to perform a full factory reset of the unit. REBOOT: Momentarily press this button, after the unit is already powered on, to reboot the unit. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Page 7
DC 12V: Plug the 12V DC power adapter into the unit and connect it to an AC wall outlet for power. ON/OFF: Flip this switch to turn the unit ON or OFF after connecting a 12V power source. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
SERIAL CONTROL UNIT REMOTE SYSTEM PIN DEFINTION PIN DEFINTION Baud Rate: 19200bps Data Bits: Parity Bits: None Stop Bits: Flow Control: None 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
[TEMPERATURE THRESHOLD IN °C] N3 = 0 ~ 100 [FAN SPEED IN PERCENT] Note: Commands will not be executed unless followed by a carriage return <CR>. In addition commands are not case-sensitive unless specified. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Page 10
This will establish communication to the desired unit to control. Type “help” to list the available commands. Note: The unit’s default IP address is 192.168.1.50. If the IP address is changed then the IP address required for Telnet access will also change accordingly. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Select the desired device. Click on the dropdown bar in the “Select a configuration task” field. Select “Set IP Address” and click Next. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Page 12
In the next section the “IP Address” field will display the assigned IP address of the desired device. Copy the IP address and paste it to the address bar of your internet browser. Note: The unit’s default IP address is 192.168.1.50 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Page 13
All primary functions of this unit are controllable via the built in WebGUI, including Status, Device Settings, Schedule, and System Settings. The individual functions will be introduced in the following section. Status This tab displays the current status of the various components of the unit in real-time. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Page 14
Note: The highest of the three System Temperature measurements is used to determine which Auto Fan Mode speed (low, middle, or high) is active when Auto Fan Mode is enabled. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Page 15
8 power ports on this unit. Repeat Mode: Items in this section will execute at their set times on the selected days (Sunday through Saturday) every week as long as they are marked as “Active”. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Page 16
Note: Each schedule item must be set as “Active” in order for it to activate at the desired scheduled time. System Settings This tab provides system configuration options including changing the network settings, downloading/restoring saved system configurations, modifying the username and password, system time setting, and updating the firmware. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
Page 17
PC for restoration later. (5) Restore Configuration: This section allows user to restore a previously downloaded system configuration. (6) Firmware Upgrade: This section allows for new firmware to be uploaded into the unit. 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
2-pin Terminal Block to DC Power SERV. CONTROL DC 12V Adapter Cable x 8 Fan Power/Control Cable x 1 8.33” PS-8DC-5V 3.2mm to 9-pin D-sub Adapter Cable x 1 PS-8DC-5V ISP/ RESET RS232 5V DC Power Manager 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)
The PS-8DC Power Manager Series contains no user serviceable components. If you have a problem with your unit, please contact the Customer Service Department. To facilitate our return/ repair processing please contact Broadata Communications, Inc. to obtain a Return Material Authorization (RMA). Please include the following information: •...
LIMITED WARRANTY 6.0 LIMITED WARRANTY Broadata Communications, Inc. (BCI) warrants, for a period of one year from date of ship- ment, each product sold shall be free from defects in material and workmanship. BCI will correct, either by repair, or at BCI’s election, by replacement, any said products that in our sole discretion prove to be defective and are returned to the manufacturing location within 30 days after such defect is ascertained.
Page 22
Broadata Communications, Inc. 2545 West 237th Street, Suite K Torrance, CA 90505 1-800-214-0222 (310) 530-1416 (310) 530-5958 (Facsimile) e-mail: Sales@Broadatacom.com 2545 West 237th Street Website: www.broadatacom.com Torrance, CA 90505 800•214•0222 310•530•1416 e-mail: Sales@broadatacom.com www.broadatacom.com 8-Port DC Power Manager User Manual (PS-8DC-5V/12V/24V/48V)- 60000PS8DCXV...