Advertisement
Quick Links
Advertisement
Related Manuals for Hoshizaki MODwater Series
Summary of Contents for Hoshizaki MODwater Series
- Page 1 Water Dispenser Model:...
-
Page 2: Front View
Contents MODwater Dispenser Model DWM-20A Front view FILTER LIFE (GREEN) if blinking, replace the filters DWM-20A FILTER HOT WATER HOT WATER AVAILABILITY (RED) if off, disable child safety switch SPARKLING WATER (Green) CHILLED WATER (Blue) NOZZLE GUARD HOT WATER (Red) NOZZLE ALKALINE WATER (Purple) DRIP PAN... - Page 3 Installa on Kit Contents –in-One Filters (2 pcs) HS-5441 3/8” Tube (20 ) for water in for drain 1/4” Tube (15 ) for CO2 Leak Detector (2pcs) Alkaline Chamber HS-5442 Water Pressure Regulator 3/8” Tube 2-Way Divider (2pcs) 3/8” Angle Stop Valve Regulator Power Cord Red Collet Locking Clip 1/4”...
- Page 4 To be posi oned on any countertop, or on top of a AM-50 / C-80 HOSHIZAKI ice makers 1.3 in All-in-One Filters (2 pcs.) - HS-5441- (Included) To be posi oned under the sink, or at any loca on near to the main water line, no more than 10...
- Page 5 Instruc ons 1. Make certain that installa on of the DWM-20A model complies with all federal, state, and local laws and regula ons as well as with your building codes, office/apartment or condo provisions, rules or regula ons. 2. In the DWM-20A dispenser you must only use the HS-5541 Filtra on System. The Manufacturer is not responsible for any misuse or modifica on of the HS-5541 Filtra on System and accepts NO liabili es if the DWM-20A is used with different filtra on systems.
- Page 6 6. Locate the 3/8” tubing found in the installa on kit. Cut a short tube sec on to connect the angle stop valve to the pressure regulator, as provided in the installa on kit (fig 4). TIP: To connect the tube, simply push the tube into the fi...
- Page 7 CO Tank Replacement 1. Fully close the main valve on top of the CO2 tank by twisting the knob. 2. Release pressure by touching the green sparkling bu on on the dispenser and dispensing sparkling water. 3. Shut the valve on the CO2 regulator, turning it counter-clockwise. 4.
- Page 8 Step-by-Step Setup DWM-20A Dispenser Tank All-in-One Filters Regulator FRONT VIEW OF A COMPLETED INSTALLATION...
- Page 9 BACK VIEW OF THE COMPLETED INSTALLATION (A) 3/8” Manual shut off valve (B) 65PSI 3/8” Pressure regulator (C) 3/8” Angle stop valve (D) Leak detector x 2pcs x 22pcs (E) Double gauge CO regulator (F) 3/8” Tube 2-way divider (G) Double All-in-One Filter (H) CO2 Gas tank (I) Flow preven on valve (ASSE 1032) (J) Power Cord...
- Page 10 BACK VIEW Temporary water line Warm air blown out (C) 3/8” Angle Stop Valve (B) 65PSI 3/8” Pressure Regulator (I) Flow Preven on Valve (ASSE 1032) 3) Prepare a temporary water line to connect the dispenser and power it up. 4) At this me, while the dispenser has started, you might need to drill a 3/4”...
- Page 11 Flush the two All-in-One filters in the sink, not through the dispenser Step 3 – Connect all the Components and close the water lines: 20) Now it is me to connect all the components using the 3/8” tube provided. At this point you can also run the 1/4" tube (C02 gas line) from the back of the dispenser to the loca on where the CO2 tank is going to be posi oned.
- Page 12 27) Dispense some water from the dispenser. 28) Check that there are no leaks at the end of your installa on. 29) Do a final check to all water lines, insert the red collet locking clips at each water connec on. Step 5 –...
- Page 13 NOTICE: the DMW-20A cannot be mounted on the wood door system -DS version of the AM-50/C-80 models Moun ng Brackets for the DWM-20A and AM-50/C-80 How anchor the DWM-20A on top of ice maker AM-50 or C-80.
- Page 14 Water Water Source Source Back Back Corner Completed Installa on of DWM-20 on AM-50/C-80...
- Page 15 Drain Pan Connec ons The drain pan comes connected to a drain pipe that runs underneath the dispenser and can be connected to a drain - via a flexible plas c tube - connected from the back of the DWM-20A dispenser. Alterna vely, if the loca on where the dispenser is installed has no drain, you must detach the metal pipe underneath the drain pan and place the plug at the bo om of the drain pan.
- Page 16 Opera on Manual Dispensing Alkaline Water Touch and hold the purple bu on to dispense alkaline water (fig 9). Chilled S ll Water Touch and hold the blue bu on to dispense chilled water (fig 10). Chilled Sparkling Water Touch and hold the green bu on to dispense chilled sparkling water. Increase the bubble level to desired fizziness level as described below (fig 11).
- Page 17 Drain Pan If the drain pan is NOT connected to its drain line, it must be regularly emp ed. • Gently pull the drain pan with care to avoid spilling. • Empty the water inside and clean the drain pan with soapy water if necessary. •...
- Page 18 Areas of Maintenance: Rou ne sani za on of the DWM-20A dispenser should be performed on the following parts: 1) Nozzle 2) Nozzle Guard 3) Front Plate Dispensing Area 4) Drain Pan Top 5) Drain Pan Bo om SPARKLING CHILLED ALKALINE 2) Nozzle Guard 1) Nozzle...
- Page 19 D. Insert a new aerator and o-ring into the nozzle cap and screw the assembly back into the nozzle. F. Mount the nozzle guard back onto the dispenser. Nozzle p 2) Replacing the Air Filter A. The air filter is located underneath the dispenser. While wearing sanitary gloves, slide the air filter out of the machine.
- Page 20 K. Re-insert the water line into the “WATER IN” port on the back of the dispenser and re-open the main water line valve. Now flush the Alkaline Chamber by dispensing approximately 2 gallons of alkaline water using the purple bu on. When the alkaline water comes out clear, the dispenser is ready.
- Page 21 HOW TO CHANGE THE ALKALINE CHAMBER: 1. Shut off water and relieve line pressure. 2. Hold head firmly. Rotate the old cartridge clockwise 1/4 turn and pull it out. 3. Pull cartridge down and out of the head. 4. Hold head firmly. Insert new cartridge into the filter head. 5.
- Page 22 the DWM-20A dispenser must be plugged directly into 110/120 VAC, 60Hz wall outlet only (15 Amps). An 15A - 125VAC/250VAC, circuit breaker is installed on the dispenser and the circuit breaker can be accessed for reset at the back of the dispenser (i.e. Power Reset Bu on).
- Page 23 Check that the dispenser is NOT in its “sleep mode”. If the green dot light indicator (top right of the front plate) is illuminated, the dispenser is simply “sleeping”. Touch any bu on for a few seconds to start. If ALL lights are off...
- Page 24 The water is flat: the CO2 tank is empty. Check the CO2 regulator to ensure that this is not the case. The tank is not empty, but the pressure gauge is set too low: Follow the Manual, raise the CO2 pressure according to the table on page 30. The tank is no empty, the pressure gauge is set correctly but the sparkling water is s ll flat: the CO2 solenoid valve may be stuck.
- Page 25 Warranty Condi ons Three-Year Limited Warranty for DWM-20A dispenser to consumers. This Limited Warranty is only valid for the United States of America and its territories. For installa ons outside of the USA call 1 (800)-438-6087 to receive related Warranty. The manufacturer warrants this dispenser against defects in material or workmanship for a period of three years, if this dispenser is purchased either directly from the manufacturer or from its authorized retailers or distributors.