Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Travis Industries Manuals
  4. Burner
  5. 864 HO NB
  6. Installation instructions manual

Travis Industries 864 HO NB Diamond-Fyre Installation Instructions Manual

Hide thumbs Also See for 864 HO NB Diamond-Fyre:

Advertisement

Quick Links

Download this manual See also: Owner's Manual, Installation Manual
Compatibility
864 HO NB
Additional Items Required
 864 HO NB Diamond-Fyre Firebacks
(96100832 Stainless, 96100833 Black Enamel, or 96100834 Black Painted)
 Driftwood Log Set "B" (94500572) or Fyre-Stone Set "C" (94700764)
 Crushed Glass (94500580 Platinum, 94500581 Bronze, or 94500582 Cobalt)
Installation Warnings
Make sure electricity to the fireplace is shut off prior to servicing. Disable the circuit
breaker or disconnect the electrical hookup before proceeding.
Make sure the gas control valve is OFF and the heater is cool before servicing.
Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
The burner must be correctly positioned before installing the media. Make sure the burner
is fully seated and the pilot is properly aligned.
Packing List
(4) #8 3/8" Screws
Light Tray
Page 1 of 13
864 HO NB Diamond-Fyre Burner
Installation Instructions
Cover Plate
Log Support
(Driftwood only)
17601700 — 2/27/14
Burner and media tray
NOTE: The media tray is shipped attached to the burner.
(sku: 96900142)
Pilot Air Shield
Burner Brackets
(Driftwood only)
© Travis Industries, Inc.
Front Burner Skirt
Air Deflector

Advertisement

loading

Related Manuals for Travis Industries 864 HO NB Diamond-Fyre

Summary of Contents for Travis Industries 864 HO NB Diamond-Fyre

  • Page 1 Compatibility 864 HO NB Additional Items Required  864 HO NB Diamond-Fyre Firebacks (96100832 Stainless, 96100833 Black Enamel, or 96100834 Black Painted)  Driftwood Log Set “B” (94500572) or Fyre-Stone Set “C” (94700764)  Crushed Glass (94500580 Platinum, 94500581 Bronze, or 94500582 Cobalt) Installation Warnings Make sure electricity to the fireplace is shut off prior to servicing.

  • Page 2: Installation Tips

    864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) Installation Tips If using propane (LP), convert the appliance before installing the burner. Burner Installation NOTE FOR OLDER 864 HO NB UNITS Older units were shipped with front and side burner skirts pre-installed. Remove these skirts before proceeding.
  • Page 3 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) 1. Remove the 3 screws from the burner tray (if not already removed – see previous page). 2. Install the burner skirt included with this kit using the 3 screws removed earlier.
  • Page 4 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) 4. Remove the 2 screws securing the accent light to the floor. Lift the accent light away from the floor. 5. Use wire-cutters to cut the 2 wires leading to the accent light. The accent light and wiring may be discarded (we suggest you keep the bulb as a spare).
  • Page 5 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) 8. Remove the control panel to expose the wiring (keep the screws). 9. Disconnect the wires that led to the accent light. NOTE: You may need to cut wire ties to access the wires.
  • Page 6 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) 11. Attach the cover plate included with this kit to the firebox floor where the left accent light was secured (use the screws removed earlier). Make sure the existing gasket remains in place.
  • Page 7 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) 14. Route the wires under the valve tray to the front of the fireplace. Make sure to route the wires under the gas control valve. The wiring must not contact hot or moving surfaces. Make sure to pull all of the slack out of the wires so they do not contact the bottom of the burner.
  • Page 8 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) 18. Install the firebacks as shown below. a) Remove the side fireback clips from the firebox ceiling near the front (both sides). The side fireback clips have a keyhole slot and can be removed by loosening the screw and sliding the clip out.
  • Page 9 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) 19. Remove the 2 screws holding the media tray to the burner (keep the screws). DRIFTWOOD MEDIA Use the 4 screws included with this kit to secure the two brackets (also included with this kit) to the back of the burner.
  • Page 10 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) FYRE-STONE MEDIA Use the 4 screws included with this kit to secure the two brackets (included with the Fyre-Stone kit) to the back of the burner. Install the air deflector (included with this kit) into the brackets as shown below.
  • Page 11 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) 20. Install the burner. Make sure it is fully seated (pushed to the right) and level with the fireback floor. 21. Install the media tray into the firebox and attach it to the burner with the screws removed in step 20.
  • Page 12 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) FYRE-STONE MEDIA Install the stone grids included with the stone kit. After the stone grids are in place, but before installing the stones, place the pilot shield over the right stone grid as shown below.
  • Page 13 864 HO NB Diamond-Fyre Burner Installation Instructions (sku: 96900142) DRIFTWOOD MEDIA Install the pilot shield (included with this kit) as shown below. Bend up the two tabs on the log plate (included with this kit). NOTE: The tabs for the Driftwood are not labeled. The tabs for the Dancing-Fyre are labeled “1”.