Page 5
Fig. F Fig. G DCH254 & DCH274 Fig. H DCH283 DCH273, DCH274...
Page 6
EnglisH HEAVY-DUTY CORDLESS ROTARY HAMMERDRILL DCH243, DCH253, DCH254, DCH273, DCH274, DCH283 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make D WALT one of the most reliable partners for professional power tool users.
Heavy-Duty Cordless Rotary Hammerdrill Denotes risk of electric shock. DCH243, DCH253, DCH254, DCH273, DCH274, DCH283 WALT declares that these products described under Denotes risk of fire. Technical Data are in compliance with: GENERAL POWER TOOL SAFETY WARNINGS 2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-6:2010.
EnglisH refrigerators. There is an increased risk of electric shock if will do the job better and safer at the rate for which it your body is earthed or grounded. was designed. c ) Do not expose power tools to rain or wet conditions. b ) Do not use the power tool if the switch does not turn Water entering a power tool will increase the risk of it on and off.
EnglisH f ) Do not expose a battery pack or tool to fire or • Do not strike jammed bits with a hammer to dislodge them. excessive temperature. Exposure to fire or temperature Fragments of metal or material chips could dislodge and above 130 °C may cause explosion.
EnglisH Important Safety Instructions for All reassembly may result in a risk of electric shock, electrocution or fire. Battery Chargers • In case of damaged power supply cord the supply cord must SAVE THESE INSTRUCTIONS: This manual contains important be replaced immediately by the manufacturer, its service agent safety and operating instructions for compatible battery or similar qualified person to prevent any hazard.
EnglisH A cold battery pack will charge at a slower rate than a warm • Charge the battery packs only in D WALT chargers. battery pack. The battery pack will charge at that slower rate • DO NOT splash or immerse in water or other liquids. throughout the entire charging cycle and will not return to •...
1. The best storage place is one that is cool and dry away more information. from direct sunlight and excess heat or cold. For optimum The DCH243, DCH253, DCH254, DCH273, DCH274, DCH283, battery performance and life, store battery packs at room operate on a 18 volt battery pack.
Mechanical Clutch Read instruction manual before use. DCH243, DCH253, DCH254, DCH283 On units fitted with a mechanical clutch the indication that the Wear ear protection. clutch has activated will be an audible ratcheting together with increased vibration.
EnglisH Active Vibration Control during tool operation and subsequent loss of control. Hold tool with both hands to maximize control. For best vibration control, hold the tool as described in Proper The side handle 5 clamps to the front of the gear case and Hand Position.
EnglisH Proper Hand Position (Fig. E) SDS Plus Bit Holder (Fig. F) nOTE: Special adapters are needed to use the SDS plus tool WARNING: To reduce the risk of serious personal injury, holder with straight shank bits and hexagonal screwdriver bits. ALWAYS use proper hand position as shown.
EnglisH To select reverse, press the forward/reverse control Various types of SDS Plus drill bits and chisels are available as button on the left side of the tool. an option. Accessories and attachments used must be regularly nOTE: The center position of the control button locks lubricated around the SDS Plus fitment.
Page 20
Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)