Remote Control Transmitter Tnqe214; Key Function Table; Important Safety Notice; Resistor - Panasonic TC-21P50R Service Manual

  

Important Safety Notice

Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacture's specified parts.
Notes:

1. Resistor

All resistors are cabon 1/4W resistor, unless marked as follows:
9
Unit of resistance is OHM [ ] (K=1,000, M=1,000,000).
: Nonflammable
: Solid
: Wire Wound
2. Capacitor
All capacitors are ceramic 50V capacitor, unless marked as follows:
m
Unit of capacitance is F, unless otherwise noted.
: Temperature Compensation
: Polyester
M
: Metalized Polyester
m
: Polypropylene
3. Coil
m
Unit of inductance is F, unless otherwise noted.
4. Test Point
: Test Point position
5. Earth Symbol
: Chassis Earth (Cold)
6. Voltage Measurement
Voltage is measured by a DC voltmeter.
Conditions of the measurement are the following:
Power Source ................................................... AC 110V-240V, 50/60Hz
Receiving Signal ............................................... Colour Bar signal (RF)
All customer's controls ...................................... Maximum positions
7. Number in red circle indicates waveform nember.
(See waveform pattern table.)
8. When arrow mark ( ) is found, connection is easily found from the direction of arrow
9. Indicates the major signal flow. : Video
10. This schematic diagram is the latest at the time of printing and subject to change without
notice.
Remarks:
1. The Power Circuit contains a circuit area which uses a separate power supply to isolate the
earth connection.
The circuit is defined by HOT and COLD indications in the schematic diagram. Take the
follwing precautions.
All circuits, except the Power Circuit, are cold.
Precautions
a. Do not touch the hot part or the hot and cold parts at the same time or you may
be shocked.
b. Do not short- circuit the hot and cold circuits or a fuse may blow and parts may
break.
c. Do not connect an instrument, such as an oscilloscope, to the hot and cold
circuits simultaneously or a fuse may blow.
Connect the earth of instruments to the earth connection of the circuit being
measured.
d. Make sure to disconnect the power plug before removing the chassis.
2. Following diodes are interchangeable.
MA150- MA162 (Replacement part)
: Metal Oxide
: Metal Film
: Fuse:
: Electrolytic
NP
: Bipolar
: Dipped Tantalum
T
: Z-Type
Z
: Line Earth (Hot)
Audio
- 23 -

Remote Control Transmitter TNQE214

D1002
VDD
2.2 - 3.5V
D1003
1 POD2
R1001
2 POD3
3 INT
D1004
D1001
POE0
4
TP1
POE1
5
6 POE2
TP4
7
POE3
Q1001
8 REM
VDD
9
TP3
C1001
XOUT
10
TP2
11 XIN
GND
12
D1005
X1001
RST
13
WOOUT
14
J1001
IC1001
C1002

Key Function Table

Key Key
Function
No. No.
1 MUTE 23
2 R-TUNE 24
3 TV/AV 25
4 VCR/LD:REW 26
5 VCR/LD:STOP 27
6 VCR/LD:FF 28
7 VCR/LD:PLAY 29
8 VCR/LD:POWER ON/OFF 30
9 CH 3 31
10 CH 2 32
11 POS. UP 33
12 LD FUNCTION 34
13 VCRADVANCE/LD:DISC A 35
14 VCR:REC/LD:DISC B 36
15 VCR FUNCTION 37
16 CH 1 38
17 CH 6 39
18 CH 5 40
19 POS. DOWN 41
20 UP 42
21 VCR/LD:PAUSE 43
22 VCR:REC 44
TP7
POD1 28
TP8
POD0 27
TP9
POC3 26
TP10
POC2
25
TP11
POC1
24
TP12
POC0 23
22 1 9 17 25 33 41
POB3
POB2 21 2 10 18 26 34 42
POB1
20 3 11 19 27 35 43
POB0
19 4 12 20 28 36 44
POA3 18 5 13 21 29 37 45
POA2
17 6 14 22 30 38 46
POA1 16 7 15 23 31 39 47
15
POA0 8 16 24 32 40 48
Key
Function
No.
MAIN MENU 45 SURROUND
CH 4 46 WAKE UP
CH 9 47
CH 8 48
VOL. UP 49
N (NORNAL) 50
RIGHT 51
VCR:CH UP/LD:SKIP + 52 TIME/TEXT
LEFT 53
CH 7 54 OFF TIMER
2 DIGIT 55
CH 0/10 56
VOL. DOWN 57
DOWN 58
SOUND MENU 59
VCR:CH DOWN/LD:SKIP - 60 LIST STORE
PICTURE MENU 61 LIST/F/TEXT
RECALL 62
INDEX 63 DISP CANCEL
F/T/B 64 POWER ON/OFF
HOLD
STEREO
TP5 TP6
TP13
49 57
TP14
50 58
TP15
51 59
TP16
52 60
TP17
53 61
TP18
54 62
TP19
55 63
TP20
56 64
Function
P .AI
TV/TEXT
Y
G
C
REVEAL
F.P .
R
--------
--------
--------
D.PNR