Advertisement
Available languages
Available languages
Table 2: Address DIP switch settings
DIP switches 1/2/3/4*
Advisor Advanced
bus address
0000
Not allowed
1000
1
0100
2
1100
3
0010
4
1010
1
0110
2
1110
3
0001
4
1001
1
0101
2
1101
3
0011
4
1011
1
0111
2
1111
3
0 — Off, 1 — On
*
Address 1 configuration is shown in Figure 3.
Powering up ATS1238
1.
Before powering up the panel and receiver module, verify
that all wiring at the panel and ATS1238 wireless receiver
is correct.
2.
Connect the panel backup battery and AC power.
Configuring wireless sensors, zones, and
PIR cameras
Refer to Advisor Advanced Installation and Programming
Manual for details.
Connection quality
See Advisor Advanced Installation and Programming Manual
for more information.
Verifying the connection quality via control panel menu
You can verify the connection quality using appropriate control
panel internal menus.
The approximate connection quality levels are listed in Table 3
below.
Table 3: RSSI values
Value
Screen bar
Received signal
(dBm)
indicator
<−90
[.I.........]
Weak signal. The senor may work, but the
operation is not recommended, because the
wireless device will cause RF supervisory
faults.
−90 to −75 [.I.I.......]
Good signal. The sensor works, although
supervision for this RF device may have to
be switched off.
P/N 1079519 (ML) • REV C • ISS 15OCT13
Value
(dBm)
Frequency
hopping pattern
−74 to −53
−52 to −37
Not allowed
>−37
1
2
HDR receiver communication quality is measured in
percentage, from 0% (no signal) to 100% (best signal).
3
4
Verifying the connection quality via camera range test
5
Range test allows you to verify wireless PIR camera signal
6
reception. In this mode, selected wireless PIR cameras show
7
the reception quality with alarm LED colour:
•
8
•
9
10
•
11
The LED follows the weakest communication link of LDR and
12
HDR.
13
14
Privacy note
15
Prior to dismantling the system, or replacing ATS1238 wireless
expander or one of wireless PIR cameras, ensure that all
stored pictures have been deleted. It takes approximately 3
minutes to delete all pictures.
Supported wireless devices
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Specifications
Compatibility
Supply voltage
Screen bar
Received signal
indicator
[.I.I.I.....]
Strong signal
[.I.I.I.I...]
[.I.I.I.I.I.]
Green: Strong signal, RSSI>−75 dBm and QI>70%
Orange: Good signal, RSSI is −90 to −75 dBm, or QI is 51
to 70%
Red: Weak signal, RSSI is <−90 dBm, or QI is <51%
TX-2344-03-1 Wireless mirror PIR camera 868 MHz, white
TX-1011-03-1 Wireless Slimline door/window contact,
868 MHz GEN2, white
TX-1011-03-3 Wireless Slimline door/window contact,
868 MHz GEN2, brown
TX-1211-03-1 Universal Transmitter, 868 MHz GEN2,
white
TX-1211-03-3 Universal Transmitter, 868 MHz GEN2,
brown
TX-2211-03-1 Wireless PIR motion sensor, 868 MHz
GEN2
TX-2212-03-1 Mirror PIR, 868 MHz GEN2, Pet Immune
TX-2411-03-1 Wireless PIR/MW motion sensor, 868 MHz
GEN2
TX-6211-03-1 Wireless optical smoke/heat sensor,
868 MHz GEN2
TX-6212-03-1 Wireless optical smoke/heat sensor,
868 MHz GEN2
TX-4131-03-2 Wireless 4-button keyfob, 868 MHz GEN2
TX-3011-03-1 868 GEN2 2-button pendant panic, white
TX-5011-03-1 Shock sensor, 868 MHz GEN2, white
TX-5011-03-3 Shock sensor, 868 MHz GEN2, brown
ATS1238 requires:
- Advisor Advanced control panel in large
polycarbonate housing, for example,
ATS1000A-LP, ATS1000A-IP-LP.
- Advisor Advanced control panel with
firmware version MR_022.022.0110 or
later.
- 868 MHz AM Learn Mode wireless
sensors and PIR cameras. See
"Supported wireless devices" above.
9 to 15 V
±2%
3 / 32
Advertisement
