SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Page 3
4. ® Your new TAPCO amplifier is designed to set up quickly and operate easily. We know it’s often seen as a sign of weakness to read a manual, along with asking for directions when lost, but maybe you can read the rest when nobody is looking.
Getting Started The following steps will help you set up your amplifier, and get the levels just right. SETTINGS: 1. Be sure the amplifier’s POWER switch is off. 2. Turn down both Level controls. 3. On the rear panel, set the SUBSONIC FILTER switch OFF and the CLIP LIMIT switch ON.
Juice Series Block Diagram ...18 TAPCO Limited Warranty ...19 Don’t forget to visit our website at www.tapcogear.com for more information about this and other TAPCO products. • If you shut down your equipment, turn off the amplifiers first. When powering up, turn on the amplifiers last.
In essence, TAPCO re-defined the price performance ratio and made high-quality professional audio mixers accessible to virtually anyone. Today, TAPCO is reborn with the same ideals and is backed by the world-class engineering and manufacturing horsepower of Mackie. The TAPCO J•800, J•1400, and J•2500 are the first power amplifiers in the TAPCO family.
STEREO BRIDGE TO SPEAKERS CHANNEL 1 CHANNEL 1 BREAKER CHANNEL 1 DESIGNED IN WOODINVILLE, WA, USA "TAPCO" IS A REGISTERED TRADEMARK OF LOUD TECHNOLOGIES INC. Passive Speakers (Mackie C300s) TO SPEAKERS CHANNEL 1 CHANNEL 1 BREAKER CHANNEL 1 DESIGNED IN WOODINVILLE, WA, USA "TAPCO"...
(i.e., the mixer’s master faders) or the amplifier’s Level controls. CHANNEL 1 BRIDGED BREAKER SPEAKER CONNECTION BRIDGED CHANNEL 1 DESIGNED IN WOODINVILLE, WA, USA "TAPCO" IS A REGISTERED TRADEMARK OF LOUD TECHNOLOGIES INC. POWER...
6. BREAKER This is a resettable circuit breaker that monitors the amount of current being drawn by the amplifier. Under normal operating conditions, this should never pop. An unusual condition may cause the breaker to pop, such as a mains voltage surge occurring at the same time as a peak amplifier output.
(mixing console, equalizer, etc.) and the balanced inputs to the amplifier. If you are using unbalanced inputs, use a high-quality 2-conductor shielded cable. Your TAPCO Dealer can recommend a suitable cable for your application. When connecting a balanced signal, the...
CHANNEL 1 CHANNEL 1 BREAKER BREAKER CHANNEL 1 DESIGNED IN WOODINVILLE, WA, USA "TAPCO" IS A REGISTERED TRADEMARK OF LOUD TECHNOLOGIES INC. Passive Speakers (Mackie C300s) CHANNEL 1 DESIGNED IN WOODINVILLE, WA, USA "TAPCO" IS A REGISTERED TRADEMARK OF LOUD TECHNOLOGIES INC.
Page 12
Stereo and Mono Modes Binding Posts When using the binding post outputs in stereo or mono modes, you can terminate your speaker cables with single or double banana plugs, spade lugs, or leave them unterminated (bare wires): unscrew the amp’s binding posts enough to reveal the holes on their sides, then insert your stripped wires (stripped about 3/8"...
Page 13
Dual-Channel Connection The BRIDGED connector has the added feature of providing both speaker outputs on a single connector. This allows you to use a single cable to carry both channels from the amplifier to the speakers. Many speakers with Speakon connectors provide an Input connector and a “Thru”...
Appendix A: Service Information Warranty Service Details concerning Warranty Service are spelled out in the Warranty section on page 19. If you think your amplifier has a problem, please do everything you can to confirm it before calling for service. Doing so might save you from the deprivation of your amplifier and the associated suffering.
Request Number, please let Tech Support know if you need new packaging. You can order new packaging through our parts department. TAPCO is not responsible for any damage that occurs due to non-factory packaging. 5. Include a legible note stating your name, shipping address (no P.O.
Appendix B: Technical Info Do The Math: Ohms, Loads, and Such An ohm is a unit of resistance — the more ohms, the more resistance (or, more accurately in this case, impedance). The more the resistance, the less the power. If you’re dealing with just one speaker (or cabinet) per output, the load in ohms is usually printed on it somewhere.
Turn On Delay 2.5 seconds “TAPCO” is a registered trademark of LOUD Technologies Inc. “Juice” is a trademark of LOUD Technologies Inc. All other brand names mentioned are trademarks or registered trademarks of their respective holders, and are hereby acknowledged.
LOUD Technologies or its authorized dealers. B. Failure to register online or return the product registration card will not void the one-year warranty. C. Service and repairs of TAPCO products are to be performed only at a factory-authorized service center. Unauthorized service, repairs, or modification will void this warranty.