Related Manuals for TANDBERG Management Server D13939
Summary of Contents for TANDBERG Management Server D13939
-
Page 1: Management Server
Management Server Quick Setup Guide D13939 Rev 04 This document is not to be reproduced in whole or in part without permission in writing from:... -
Page 2: Trademarks And Copyright
The information in this document is furnished for informational purposes only, is subject to change without prior notice, and should not be construed as a commitment by TANDBERG. The information in this document is believed to be accurate and reliable; however TANDBERG... -
Page 3: Environmental Issues
Waste handling There is no need to send any products or material back to TANDBERG as there are no consumables to take care of. Please contact your local dealer for information on local waste handling and recycling of electronic products. -
Page 4: Operator Safety Summary
TANDBERG Management Server Quick Setup Guide Operator Safety Summary For your protection, please read these safety instructions completely before operating the equipment and keep this manual for future reference. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructions both on the apparatus and in the operating instructions. - Page 5 Servicing - Do not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to qualified service personnel. Damaged Equipment - Unplug the apparatus from the outlet and refer servicing to qualified personnel under the following conditions: When the power cord or plug is damaged or frayed If liquid has been spilled or objects have fallen into the apparatus...
- Page 6 TANDBERG Management Server Quick Setup Guide Contact us If you have any questions, comments or suggestions, please see the Online Support service at www.tandberg.com It is also possible to send a fax or mail to the attention of: Product and Sales Support TANDBERG P.O.
- Page 7 Quick Setup Guide End-User License Information IMPORTANT: THE USER MANUAL CD FOR THIS PRODUCT CONTAINS IMPORTANT TERMS AND CONDITIONS INCLUDING END USER LICENSE AGREEMENTS. THE LICENSE AGREEMENTS SHOULD BE READ PRIOR TO USE. USE OF THIS PRODUCT CONSTITUTES ACCEPTANCE OF THE TERMS OF THE LICENSES.
-
Page 8: Table Of Contents
How to restart the Management Server ... 16 4.1.2 How to shutdown the Management Server... 17 4.2 Client Software Requirements... 17 Administrator Settings ... 19 5.1 Operating System Settings... 19 5.2 TANDBERG Management Suite Settings ... 20 5.3 Added systems ... 22 viii... -
Page 9: Introduction
The TANDBERG Management Server is a server that comes with the TANDBERG Management Suite (TMS) pre-installed. This guide will take you through the initial steps of setting up the TANDBERG Management Server before first time use. Please refer to the Getting Started section of the TANDBERG Management Suite Installation Manual –... -
Page 10: Installation
TANDBERG Management Server Quick Setup Guide 2 Installation Precautions: Never install communication wiring during a lightning storm. Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations. Never touch uninstalled communication wires or terminals unless the communication line has been disconnected at the network interface. -
Page 11: Unpacking
The Management Server comes with rubber feet for standalone installation and brackets for mounting in standard 19” racks. Before starting the rack mounting please make sure the TANDBERG Management Server is placed securely on a hard flat surface. 1. Disconnect the AC power cable. -
Page 12: Connecting Cables
TANDBERG Management Server Quick Setup Guide 2.2 Connecting cables LAN cable Connect a LAN cable from the ‘LAN 1’ connector on the Management Server to your network. The LAN 2, 3 and 4’ connectors are not used and should be left open. -
Page 13: Ip Address Setting Configuration
2.3 IP Address Setting Configuration The Management Server requires the IP Address Settings to be configured before it can be used. IP Address Configuration can be made using the LCD Panel. Front view of the Management Server with the LCD panel: LCD Panel buttons and their functions: Up and Down arrows... - Page 14 TANDBERG Management Server Quick Setup Guide 5. Move between characters by using the Up and Down arrows. Edit values by pressing Enter and using the Up or Down arrow to modify. Press Enter again to confirm the value, or press Return to restore the value to its previous state.
-
Page 15: Product Registration And Updates
Quick Setup Guide 3 Product Registration and Updates You need to register the product if you would like to receive an email from TANDBERG Constant Care Services when Management Server updates to the TANDBERG Management Server become available. You can also check the following ftp site for all available downloads: http://ftp.tandberg.net/pub/software/tms/... -
Page 16: General Use
TANDBERG Management Server Quick Setup Guide 4 General Use TANDBERG Management Server The Management Server should always be turned on. The unit itself should not be available to users at any time. If the system does not respond: Check the LCD panel to determine if the unit is switched on and ‘live’. -
Page 17: How To Shutdown The Management Server
4.1.2 How to shutdown the Management Server 1. Press Enter to display the Main Menu screen. 2. From the Main Menu screen, use the Up or Down arrow to select Commands. 3. Press Enter to confirm your selection. 4. From the Commands menu, use the Up or Down arrow to select Shutdown and press Enter. 5. -
Page 19: Administrator Settings
5 Administrator Settings Before the TANDBERG Management Server can be taken into use, some basic settings need to be configured. 5.1 Operating System Settings You can access the Web User Interface for Microsoft Windows Server administration to configure operating system settings. -
Page 20: Tandberg Management Suite Settings
From the Maintenance tab, you can set the date, time and time-zone. 5.2 TANDBERG Management Suite Settings You can access the Web User Interface for the TANDBERG Management Suite (TMS) to configure TMS settings. 1. Start a web browser and enter the address of the Management Server. - Page 21 Set the Default Time Zone to where the majority of the TMS users are situated to simplify user setup. Select the Administrative Tools > Configuration > Network Settings menu item and scroll down to the TMS Services section to set the scan range TMS uses to search for new systems. By default TMS scans the entire network for systems, i.e.
-
Page 22: Added Systems
TMS will use to send emails and the email address these will be sent from. 5.3 Added systems The TANDBERG Management Server comes with automatic registration of systems enabled. TMS will therefore after turning it on the first time, search the network for systems. These systems will be added in folder called ‘Discovered Systems’...