Page 1
PCV-R556DS/R558DS SERVICE MANUAL US Model Canadian Model S400 Specifications PERSONAL COMPUTER VAIO 9-928-377-11...
Page 2
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Confidential – 2 – PCV-R556DS/R558DS (UC)
2-2. REAR PANEL Note on mounting rear panel: When installation rear panel, refer to figure. GOOD claw 4 rear panel rear panel claw 1 two claws rear panel 3 claw 2 two claws 2-3. TOP COVER, LEFT COVER, RIGHT COVER AND TOP COVER CHASSIS 1 three screws (unified 4.5) 2 five claws...
2-5. 3 four screws (unified 4.5) 4 Remove HDD and HDD bracket in the direction of arrow A. 5 two screws (W) (No.6-32UNC) 6 HDD 2 harness (IDE/ATA66) 5 two screws (W) (No.6-32UNC) 1 power connector 2-6. VGA CARD 3 VGA card 1 screw (W) (No.6-32UNC) 2 Push the AGP clip.
2-9. POWER SUPPLY 2 three screws (PS No.6-32UNC) 6 boss 3 Remove power supply, PS bracket ass’y and PS fan duct in the direction of arrow A . 7 PS fan duct 4 three screws (unified 4.5) 5 power supply 1 Disconnect respective power connectors 2 screw...
2-17. CPU 3 Elect the lever in the direction of arrow A . 1 heat sink holder 4 CPU 2 heat sink Precaution on mounting the heat sink holder: Check that the angle B shown in figure does not exceed 90 degrees, when the heat sink was removed or if the heat sink mounting failed.
2-19. MAIN ELECTRIC PARTS ARRANGEMENT memory (DIMM) DVD-ROM CD-RW power supply SWX-38 mount VGA card modem card CNX-94 mount mother board Confidential PCV-R556DS/R558DS (UC) 2-12 (END)
SECTION 4 PROGRAM FOR SERVICE 4-1. General Description Enter the model name (.BAT file name), then press the Return key. [Input example] In the case of PCV-R556DS The Diag for service is available in the following three kinds: X:\PCDR>R556 [↵] 1.
[Example of log file] PC-DOCTOR 2.0 SYSTEM TEST LOG ================================ Inventory ........CPU MHz is too low (700 vs 750) Inventory FAILED Press the F9 key (Exit program) to return to the prompt, where the system waits for the next command. X:\PCDR\R556>_ To start another Diag, remove the floppy disk, and restart the system.
SECTION 5 SERVICE INFORMATION 5-1. JUMPER SETTING ON HARD DISK DRIVE The hard disk drive of service parts can be used without changing factory jumper setting, when it was replaced for service. Capacity Model Part No. Maker Code (formatted) PCV-R556DS 1-772-712-11 Maxtor 93073U6...
5-2. JUMPER SETTING OF MOTHERBOARD The Motherboard of service parts can be used without changing factory jumper setting, when it was replaced for service. CMOS CLR SAFE_EN RBT_EN CMOS CLR CAUTION Do not change the jumper with the power turned on. Before changing the jumper, turn off the power and disconnect the power cord from the set.
Page 23
SECTION 6 FRAME HARNESS 6-1. CONNECTOR LIST CUSL-LE MOTHER BOARD Internal Connector Power Supply Connector location on MB See the frame harness diagram 20pin ATX type connector. pin assignments : Reffered as ATXPWR Connector location on MB Signal Name Signal Name See the frame harness diagram Ground HDsel...
Page 24
Battery Holder & Battery Ground Holder location on MB See the frame harness diagram Battery vender Sony CR2032 or equivalent VIDEO (not installed *) 4 pin standard 2mm single line header for Video signal input PADDLE_CON (not installed pin assingments:...
Page 25
Game/Line Out(Headphone) /Line In/Microphone Jack Serial (COM1) Connector location on MB In rear I/O window Connector location on MB In rear I/O window pin assignments : Game port pin assignments : Signal Name Signal Name GAMEVCC Serial In # JPYB0 Serial Out # JOYA0 DTR#...