Table of Contents
Advertisement
- This manual is designed to help you to install, operate and maintain Trimming System
FC-11. Read, understand and keep this manual in a safe and convenient place.
- Do not operate FC-11 until you read and understand the instructions in this manual.
- Horizon International Inc. shall not be liable for incidental consequential damages result-
ing from : improper or inadequate maintenance by customer; unauthorized modification or
misuse; operation outside of the environmental specifications for the product.
- Horizon International Inc. pursues a policy of continuing improvement in design and
performance of the product. Therefore, the product design and specifications are subject to
change without prior notice and without our legal obligation.
- All rights are reserved. No part of the manual may be photocopied, reproduced or trans-
lated to another language without the prior written consent of Horizon International Inc.
010322/FC11/02E/DV
T R I M M E R
Important Information
FC-11
I
UM201033-02
Advertisement
Table of Contents
Related Manuals for Horizon Fitness FC-11
Summary of Contents for Horizon Fitness FC-11
-
Page 1: Important Information
FC-11. Read, understand and keep this manual in a safe and convenient place. - Do not operate FC-11 until you read and understand the instructions in this manual. - Horizon International Inc. shall not be liable for incidental consequential damages result- ing from : improper or inadequate maintenance by customer;... -
Page 2: Safety Precautions
Safety Precautions - The signal word WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. - The signal word CAUTION indicates a potentially hazardous situation which, if not avoided, may result in damage on machines. It may also be used to alert against unsafe practices. -
Page 3: Table Of Contents
CONTENTS Important Information .................... I Safety Precautions ....................II 1. Before You Begin 1-1 Specifications ...................... 2 1-2 Machine Descriptions ..................3 1-2-1 Machine Descriptions and Functions..............3 [1] General View....................3 [2] Press Section ....................4 [3] In-Feed Section ....................5 [4] Operation Panel .................... -
Page 5: Before You Begin
1. Before You Begin 1. Before You Begin 1-1 Specifications ................... 2 1-2 Machine Descriptions ................3 1-3 Accessories/Option .................. 7... -
Page 6: Specifications
1. Before You Begin 1-1 Specifications Model FC-11 Cutting Dimensions Spine to fore edge : 99 to 225 mm (3.9" to 8.9") Booklet Size 100 x 200 mm to 240 x 330 mm (Before Trim) (4.0" x 7.9" to 9.4" x 12.9") Trimming Length 15 mm (0.6") -
Page 7: Machine Descriptions
1. Before You Begin 1-2 Machine Descriptions 1-2-1 Machine Descriptions and Functions [1] General View Power Switch Dust Box This section gathers Manual Handwheel trimmed paper. When power is off, release stopper pin then upper cutter can be lowered with this manual handwheel. -
Page 8: Press Section
Jam Sensor In case booklet is jammed over this section, FC-11 stops automatically. Breaker This breaker will trip when upper cutter unit is locked. Transport Belts... -
Page 9: In-Feed Section
Ejecting Roller Adjuster This adjuster is used to adjust clearance between delivery belt and ejecting roller. Ejecting Roller Delivery Belts These belts deliver booklets from FC-11 after trimming operation performed. Height of delivery belts is adjustable. -
Page 10: Operation Panel
Counter This counter indicates total number of trimming for maintenance purpose. Motor ON Lamp This lamp illuminates when FC-11 is ready for cut. Motor ON Button This button starts motor. Motor OFF Button This button stops motor. Emergency Stop Button... -
Page 11: Accessories/Option
1. Before You Begin 1-3 Accessories/Option 6. Ground Wire (GW-1) 1 pc 1. Upper Knife (M003273-01) 1 pc 2. Lower Knife (M003272-01) 7. Hold Supporter (M003327-03) 2 pcs 3. Leveling Bolt (HB12-100) 2 pc 8. Leveling Bolt 2 (6200-1005) 1 pc 4. - Page 12 1. Before You Begin...
-
Page 13: Set Up And Operation
2. Set Up and Operation 2. Set Up and Operation 2-1 Operation Procedures ................10... -
Page 14: Operation Procedures
SPF-11. Make sure that booklet is trimmed correctly. Start collating. NOTE If main motor of FC-11 is not on, main motor of SPF-11 can not be started even if motor ON button of SPF-11 is depressed. -
Page 15: Maintenance Hints
3. Maintenance Hints 3. Maintenance Hints 3-1 Upper and Lower Knife Replacement ........... 12... -
Page 16: Replacing Upper And Lower Knife
3. Maintenance Hints 3-1 Upper and Lower Knife Replacement CAUTION 1. When replacing knife, be sure to Upper Knife turn power switch off. Upper Knife Lock Bolt Lock Bolts 2. Knife edge is very sharp so utmost Lock Screw care should be taken when knife is Air Blow replaced and/or installed. -
Page 17: Installation Instructions
4. Installation Instructions 4. Installation Instructions 4-1 Installation Instructions ................14... - Page 18 Connect connector of FC-11 to recep- tacle of SPF-11. Push FC-11 to SPF-11 until cushion rubbers installed on lower FC-11 touches SPF-11. Make sure front side of FC-11 is snugly aligned with that of SPF-11. Install conveyor unit at delivery end of Conveyor FC-11 with hooks of FC-11 inserted in key holes of conveyor .