Advertisement
Control-R™ Recirculation Accessory Installation Instructions
The Control-R™ Push Button works with the Control-R™
Module to operate the Rinnai Tankless Water Heater
recirculation system. The Push Button mounts near the
point of use (such as a kitchen faucet or bathroom sink)
and activates the recirculation system with the push of a
button. The recirculation system will deactivate after five
minutes from initiation or when the water has reached the
set temperature. The Push Button is compatible only with
Rinnai Tankless Water Heaters featuring Rinnai Circ-
Logic™.
NOTE: If the recirculating pump has recently been active
and the recirculation loop is still warm, there may be a
delay in pump activation. To minimize any delay in pump
activation, set the Rinnai Tankless Water Heater to
Comfort Mode. Refer to the "Recirculation Mode" section
in the Tankless Water Heater Installation and Operation
Manual for more information on Comfort Mode.
Installation Requirements
•
Prior to installation, determine the best location for
the Push Button. Rinnai recommends installing the
Push Button near a water fixture that will be used
frequently, such as a kitchen faucet or bathroom sink.
•
The Push Button works in conjunction with the
Control-R™ Module. The Control-R™ Module must be
installed and functioning properly before installing the
Push Button.
You Will Need:
• Control-R™ module
• Push button
• Small tool/pin
Install the Push Button
IMPORTANT:
•
Make sure the module LED has been RED for
at least 1 minute prior to beginning push
button pairing process .
1
Remove the push button cover by pressing both sides
of the bottom plate and lifting the cover.
2
Pair the push button with the Control-R™ Module
(called pairing mode) by following the steps below.
IMPORTANT:
•
You have 5 minutes to pair the push button
with the module before pairing mode times
out. If pairing mode times out, you must
repeat the steps below.
a
On the module, press and hold down the Connect
button until the LED light turns GREEN. Then,
release the button.
LED
Connect button
b
Press and hold down the push
button until the button flashes three
times. Then, release the button.
c
The module LED flashes GREEN and then turns
to the previous mode (BLUE = connected to
Internet; RED = not connected to Internet).
d
The push button is now paired with the module. Replace
the cover on the push button device.
e
Once all devices have been paired, use a pin or small tool
to press the RESET button on the module to reset and wait
for it to boot up again.
IMPORTANT: Wait one minute after module
LED turns RED before trying to initiate
recirculation with the push button.
3
Determine a location for the Push Button. Rinnai recommends
installing the Push Button near a water fixture that will be used
frequently, such as a kitchen faucet or bathroom sink.
4
Remove the adhesive strip from the
back cover and firmly press the body
of the Push Button device against the
location surface to allow the adhesive
to take hold.
Operate the Push Button
Press the Push Button to activate the Rinnai Tankless Water Heater
recirculation system. The recirculation system will deactivate after
five minutes from initiation or when the water has reached the set
temperature.
NOTE: If the recirculating pump has recently been active and the
recirculation loop is still warm, there may be a delay in pump
activation. For further information, refer to the "Recirculation
Mode" section in the Tankless Water Heater Installation and
Operation Manual.
Restore Factory Settings
To restore the Push Button settings to a
fresh state, remove the two Push Button
batteries (see right). Wait a few seconds
and then reinsert the batteries while
pressing down on the Push Button.
Continue to press down on the Push
Button for an additional three seconds
after the batteries have been inserted.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION
Push Button LED
Remove adhesive strip
Advertisement
